Bluetooth: Vision, Goals, and Architecture
Jaap Haartsen Mahmoud Naghshineh Jon Inouye
Jaap.Haartsen@emn.ericsson.se mahmoud@us.ibm.com Jon.W.Inouye@intel.com
Ericsson IBM Watson Research Center Intel Corporation
Enschede, The Netherlands Hawthorne, NY, U.S.A. Chandler, AZ, U.S.A.
Olaf J. Joeressen Warren Allen
Olaf.Joeressen@nmp.nokia.com Warren.Allen@tais.toshiba.com
Nokia Mobile Phones Toshiba Corporation
Bochum, Germany Irvine, CA, U.S.A.
A few years ago it was recognized that the vision of a truly low-cost, low-power radio-based cable
replacement was feasible. Such a ubiquitous link would provide the basis for portable devices to
communicate together in an ad hoc fashion by creating personal area networks which have similar
advantages to their office environment counterpart - the local area network (LAN). Bluetooth is an
effort by a consortium of companies to design a royalty free technology specification enabling this
vision. This article describes the vision and goalsof the Bluetoothprogram and introduces the radio-
based technology.
I. Vision
In recent years, wireless connectivityhas been an active area of
research as we have witnessed a large number of government
and industry initiatives, research efforts and standard activities
that have aimed at enabling wireless and mobile networking
technologies. As a result, today we have a diverse set of wire-
less access technologies from satellite networks, to wide area
cellular systems, and from wireless local loopand PCS to wire-
less LANs. However, most of these solutionstarget narrow and
specific application scenarios. With all such efforts spent on
wireless link technologies, we still lack a universal framework
that offers a way to access information based on a diverse set
of devices (e.g., PDAs, mobile PCs, phones, pagers, etc.) in a
seamless, user-friendly and efficient manner.
Formed in February 1998 by mobile telephony and comput-
ing leaders Ericsson, IBM, Intel, Nokia, and Toshiba, the Blue-
tooth special interest group (SIG) is designing a royalty-free,
technology specification where each of the founding compa-
nies has a significant stake in enabling this vision. We believe
that Bluetooth can revolutionize wireless connectivity for per-
sonal and business mobile devices, enabling seamless voice
and data communication via short-range radio links and allow-
ing users to connect a wide range of devices easily and quickly,
without the need for cables, expanding communications capa-
bilities for mobile computers, mobile phones and other mobile
devices, both inside and outside of the office. Considering a
wide range of computing and communication devices such as
PDAs, notebook computers, pagers, and cellular phones with
different capabilities, we envisage Bluetooth to provide a solu-
tion for access to information and personal communication by
enabling a collaboration between devices in proximity of each
other where every device provides its inherent function based
on its user interface, form factor, cost and power constraints.
Furthermore, the Bluetooth technology enables many new us-
age models for portable devices. For notebook computer man-
ufacturers, the development of a short-range radio frequency
(RF) solutionenables the notebook computer to connect to dif-
ferent varieties of cellular phones and other notebook comput-
ers. For cellular handset manufacturers, the RF solution re-
moves many of the wires required for audio and data exchange.
Wireless hands-free kits operate even while the cellular phone
is stored in a purse. As an example for a new usage model, we
enable a connection from a mobile computer to the Internet us-
ing a cellular phone as a bridge. In some cases, even when the
cellular phone is stored out of plain sight inside a briefcase, for
example. In this scenario, the connection to the Internet is au-
tomatically established and auto-configured without requiring
a conscious effort on the user's part to connect the mobile com-
puter to the cellular phone and configure these two devices to
communicate. We refer to this as a hidden computing or an un-
conscious connectivity model that is a powerful paradigm for
new and exciting applications.
A very key characteristic of Bluetooth that differentiates it
from other wireless technologies is that it enables combined
usability models based on functions provided by different de-
vices. Let us consider a connection between a PDA (comput-
ing device) and a cellular phone (communicating device) using
Bluetooth and a second connection between the cellular phone
and a cellular base station providingconnectivity for both data
and voice communication. In this model, the PDA maintains
its function as a computing device and the phone maintains its
role as a communicationdevice - each one of these devices pro-
vide a specific function efficiently, yet their function is sepa-
rate and each can be used independentlyof the other. However,
when these devices are near each other they provide a useful
combined function. We believe that this function and connec-
tivity model based on a combination of wireless access tech-
nologies ­ each matched to different device capabilities and
requirements ­ is a powerful paradigm that will enable ubiq-
uitous and pervasive wireless communication. Many of these
wireless linktechnologies are available today, however there is
a need to provide a wireless connectivity, networking, and ap-
plicationframework to realize the totalsolution. Thisis exactly
the charter of the Bluetooth SIG. In addition to combining the
resources of a personal network, the RF linkcould also connect
Mobile Computing and Communications Review, Volume 1, Number 2 1
the personal network to the wired infrastructure. A data access
point in an office, conference room, or airport kiosk would act
as an information gateway for a notebook computer or cellular
handset.
The remainder of this paper is organized as follows. Sec-
tion II describes the goals the Bluetooth SIG hopes to achieve.
Section III provides an overview of the Bluetooth architecture
as it currently exists. Section IV compares the Bluetooth SIG
to other industry initiatives involving wireless technology and
Section V summarizes the article.
II. Goals
A. New Usage Models
The Bluetooth SIG is attempting to enable new usage models
and create additional benefits for users of portable telephony
and computer products. In addition to the examples presented
in Section I, the SIG wants to enable the following future pos-
sibilities.
 
The Three-in-One Phone. In this scenario, you are able to
use the same phone wherever you are. When you're at the
office, your phone functions as an intercom (no telephony
charge). At home, it functions as a portable phone (fixed
line charge). And when you're outdoors, the phone func-
tions as a mobile phone (cellular charge).
 
The Briefcase Trick. Use e-mail while your notebook is
still in the briefcase. When your notebook receives an e-
mail, you'll get an alert on your mobile phone. You can
also browse allincominge-mails and read thoseyou select
in the mobile phone's window.
 
The Automatic Synchronizer. Automatic background syn-
chronization keeps you up-to-date. Automatic synchro-
nization of data on your desktop, notebook, personal dig-
ital assistant(PDA), and mobile phone. For instance, as
soon as you enter your office the address list and calendar
in your notebook will automatically be updated to agree
with the one in your desktop, or vice versa. Collect a busi-
ness card on your phone and add it to your address list on
your notebook PC.
B. System Challenges
The usage models described above require various system re-
quirements to be met. In this section, we review several re-
quirements and the challenges they offer.
Support for both voice and data. The air protocol must sup-
port good quality real-time voice, where "good" is considered
to be wired phone line quality. Voice quality is important to
both end-users who are accustomed to it, and for speech recog-
nition engines whose accuracy depends on it.
Able to establish ad hoc connections. The dynamic nature of
mobility makes it difficult to make any assumptions about the
operating environment. Bluetooth units must be able to detect
other compatible units and establish connections to them. A
single unitmust be able to establish multipleconnections in ad-
ditionto accepting new connections while connected. Ignoring
a new connection requests while connected is confusing to the
user and deemed unacceptable, especially if we want tosupport
unconscious computing while retaining the ability to perform
interactive operations!
Able to withstand interference from other sources in an unli-
cenced band. The Bluetooth radio operates in the unlicensed
2.4 GHz band where many other RF radiators are expected
to exist. The fact that microwave ovens operating at this fre-
quency is one reason why this band is unlicensed in most coun-
tries. The challenge is to avoid significant degradation in per-
formance when other RF radiators, including other personal
area networks in nearby use, are in operation.
Worldwideuse. Not onlyare "standard" cables equippedwith
a variety of connectors, different standards exists in different
geographical locationsthroughoutthe world. Experienced mo-
bile travelers are accustomed to carrying around a number of
different power, phone, and network connectors. The chal-
lenge here is very regulatory in nature with many governments
having their own set of restrictions on RF technology. And
while the 2.4 GHz band is unlicensed through most parts of
the world, it varies in range and offset in a number of differ-
ent countries.
Similar amount of protection compared to a cable. In addi-
tionto the radio's short-range nature and spread spectrum tech-
niques, Bluetooth link protocols also provide authentication
and privacy mechanisms. Users certainly don'twant others lis-
tening in on their conversations, snooping their data transmis-
sions, or using their cellular phones for Internet access.
Small size to accommodate integration into a variety of de-
vices. The Bluetooth radio module must be small enough to
permit integration into portable devices. Wearable devices in
particular, such as mobile phones, headsets, and smart badges
have little space to spare for a radio module.
Negligible power consumption compared with the device in
which the radio is used. Many Bluetoothdevices will be bat-
tery powered. This requirement implies the integration of the
Bluetooth radio should not significantly compromise the bat-
tery lifetime of the device.
Encourage ubiquitous deployment of the technology. To
achieve this goal, the SIG is designing an open specification
defining the radio, physical, link, and higher level protocols
and services necessary to support the usage models in the vi-
sion. The Specification will be made available under favorable
adoption terms, including royalty free, to SIG members.
C. The Specification
The Bluetooth Specification defines the requirements ensuring
interoperable operation between Bluetooth devices from dif-
ferent manufacturers. The Bluetooth Specification is work-in-
progress and any material presented here is preliminary and
2 Mobile Computing and Communications Review, Volume 1, Number 2
RADIO
Application Programs
BASEBAND
LINK MANAGER
AUDIO
TCP/IP
LOGICAL LINK CONTROL
RFCOMM
Interoperability
IrDA
(OBEX)
Interoperability
WAP
Figure 1: Application Framework
subject to change without notice.
 
The Specification draft is
composed of twosets of documents: the radioand protocoldef-
initions, and the compliance requirements.
Figure 1 outlines the application framework in the context
of the radio and protocol stack. The Radio takes care of send-
ing and receiving modulated bitstreams. The Baseband (BB)
protocol defines the timing, framing, packets, and flow control
on the link. The Link Manager (LM) assumes the responsibil-
ity of managing connection states, enforcing fairness among
slaves, power management, and other management tasks. The
Logical Link Controlhandles multiplexingof higher level pro-
tocols, segmentation and reassembly of large packets, and de-
vice discovery. Audio data is mapped directly on to the Base-
band while audio control is layered above the logical link con-
trol. Above the data link layer, RFCOMM and network level
protocols provide different communication abstractions. RF-
COMM provides serial cable emulation using a subset of the
ETSI GSM 07.10 standard [2]. Other parts of the Bluetooth
Specification deal with interoperability with other protocols
and protocol stacks. Defining TCP/IP over Bluetooth requires
that bridging, address resolution, MTU definition, and mul-
ticast/broadcast mappings be solved. To accelerate the num-
ber of wireless-specific applications, the BluetoothSIG is con-
templating interoperabilitywith higher layer IrDA

and WAP

protocolstacks.

For example, IrOBEX [4] defines a transport-
independent format and session protocol for object exchange
and is used as the basis for a variety of applications from
exchanging files and business cards to synchronizing address
book and calendar schedules.
The compliance requirements section of the Specification
¤
The Bluetooth SIG disclaims all liability, including liability for infringe-
ment of any proprietaryrights, relating to use of information in this article. No
license, express or implied, by estoppel or otherwise, to any intellectual prop-
erty rights is granted herein.
Infrared Data Association. See http://www.irda.org.
Wireless Application Protocol Forum. See http://www.wapforum.org.§
Third party brands and names are the property of their respective owners.
1
Piconet A
Piconet B
0
3/2
0
1
2
Figure 2: Scatternet Example
defines the radio and protocol features that are required for dif-
ferent classes of devices. Due to the wide variety of possible
Bluetooth devices, different sets of requirements are needed.
For example, one would not expect an audio headset to have
the same minimum requirements as a notebook computer. The
goal of the Specification's compliance section is ensuring that
any device wearing a Bluetooth"logo" supportsa minimum set
of benefits for its user.
III. The Bluetooth Architecture
Bluetooth has been specified and designed with emphasis on
robustness and low cost. Its implementationis based on a high-
performance, yet low cost, integrated radio transceiver. Blue-
tooth is targeted at mobile and business users who need to es-
tablish a link, or small network, between their computer, cel-
lular phone and other peripherals. The required and nominal
range of Bluetooth radio is thus set to 10 meters (with 0 dBm
output power). To support other uses, for example the home
environment, the Bluetooth chipset can be augmented with an
external power amplifier to extend the range (up to 100m with
+20dBm output power). Auxiliary baseband hardware to sup-
port, for example, four or more voice channels can also be
added. These additionsto the base chip set are fullycompatible
with the nominal specification and may be added depending on
the application.
Bluetoothoperates in the international2.4 GHz ISM band, at
a gross data rate of1 Mbit/second, and features lowenergy con-
sumption for use in battery operated devices. Bluetooth uses
an ad hoc, piconet structure hereafter referred to as scatternet.
Figure 2 illustrates an example scatternet, with one unit par-
ticipating in both piconets. With the scatternet technology de-
scribed later in this document, it has been possible to achieve
an aggregate throughput of over 10 Mbits/second or 20 voice
channels within a fully expanded scatternet. The structure also
makes it possible to extend the radio range by simply adding
additional Bluetooth units acting as bridges at strategic places.
A single unit can support a maximum data transfer rate of
721 kbits/second or a maximum of 3 voice channels. A mix-
ture of voice and data transfer is also possible in order to sup-
port multimedia applications. A robust voice coding scheme
with a rate of 64kbits/second per voice channel is used. To
sustain these transfer rates in busy radio environment, a packet
switching protocol with frequency hopping and advanced cod-
Mobile Computing and Communications Review, Volume 1, Number 2 3
ing techniques are employed. It should also be mentioned that
the Bluetoothfeatures a graceful degradation of both voice and
data transfer rates in busy RF environments.
A. Master/Slave definitions
In the Bluetooth network all units are peer units with identical
hardware and software interfaces distinguishedby a unique 48-
bit address. At the start of a connection, the initializing unit
is temporarily assigned as a master. This assignment is valid
only during this connection. It is the master which initiates the
connection and controls the traffic on the connection. Slaves
are assigned a temporary 3-bit member address to reduce the
number of addressing bits required for active communication.
B. Network topology
The Bluetooth network supports both point-to-pointand point-
to-multipointconnections. A piconet is the network formed by
a master and one or more slaves. Each piconet is defined by a
different frequency hopping channel. All units participating in
the same piconet are synchronized to this channel.
C. Robust Air Protocol and Adaptive Range
To achieve the highest possible robustness for noisy radio en-
vironments, Bluetooth uses a packet-switching protocol based
on a frequency hop scheme with 1600 hops per second. The
entire available frequency spectrum is used with 79 hops of 1
MHz bandwidth, defined analogous to the IEEE 802.11 stan-
dard [3]. This frequency hopping gives a reasonable band-
width and the best interference immunity by utilizingthe entire
available spectrum of the open 2.4 GHz Industrial, Scientific,
and Medical (ISM) band. Virtual channels are defined using
pseudo-random hop sequences.
The frequency hopping scheme is combined with fast Au-
tomatic Repeat Request (ARQ), cyclic redundancy checks
(CRC), and Forward Error Correction (FEC) for data. For
voice a continuous variable slope delta modulation (CVSD)
scheme is used. All of this results in a very robust link for both
data and voice.
To save power and minimize radio interference problems, a
RSSI (Received Signals Strength Indicator) with a 72 dB dy-
namic range will be employed. The RSSI will measure the sig-
nal received from differentunitsand adapt the RF outputpower
to the exact requirement in each instance. That is, witha mouse
or headset, the output power could be limited to a 1 m range,
whereas a handset may need a range of 100 m or more.
D. Establishing network connections
When first establishing a network or adding components to a
piconet, the units must be identified. Units can be dynamically
connected and disconnected from the piconet at any time. Two
available optionslead to connection times of typically0.64 and
1.28 seconds respectively. This applies when the unit address
is known and not more than about 5 hours have elapsed since
the previous connection. A unit does not need to be connected
at all times since only a typical delay of under one second is
required to start a transaction. Hence, when not in use, the unit
can be ina sleep state (STANDBY) most ofthe time where only
a Low Power Oscillator (LPO) is running. This is, of course,
beneficial for battery operation.
Before any connections are made, all units are in standby
mode. In this mode, an unconnected unit will only listen to
messages every 1.28 seconds or 2.56 seconds depending on the
selected option. Each time a unit wakes up, it will listen on one
of 32 hop frequencies defined for this unit.
The connect procedure is initiated by one of the units, the
master. A connection is made either by a PAGE message if
the address is already known, or by the INQUIRY message
followed by a subsequent PAGE message if the address is un-
known. In the initial PAGE state, the paging unit (which is the
master) will send a train of 16 identical page messages on 16
different hop frequencies defined for the unit to be paged (the
slave). The train covers half the sequence of frequencies in
which the slave can wake up. It is repeated 128 or 256 times
(1.28 or 2.56 seconds) depending on the needs of the paged
unit. If no response is received after this time, the master trans-
mits a train of 16 identical page messages on the remaining 16
hop frequencies in the wake-up sequence. The maximum de-
lay before the master reaches the slave is 2 times 1.28 seconds
or 2.56 seconds if a periodicity of 1.28 seconds was chosen for
paging and 5.12 seconds with 2.56 seconds periodicity respec-
tively. This allows devices to trade off between access delay
and standby power savings.
The hop frequencies in the first page train are based on the
master's slave clock estimate. The train will include the esti-
mated wake-up hop, and 8 hops before and 7 hops after this
hop. As a result, the estimate can be
 
7 hops in error and
still the master reaches the slave with the first page train. Be-
cause the estimate is updated at each connection establishment,
the acquisition delay is shorter when a shorter time has elapsed
since the units were last connected. With a Low Power Oscil-
lator (LPO) inaccuracy better than
 
250 ppm, the first train is
still valid after at least 5-hours lapse with no connection.
That is, for a time period of at least 5 hours since the last
connection, the average acquisitiontimes are 0.64 seconds and
1.28 seconds respectively. If the first train does not cover the
slave's wakeup frequency, the second train does and the aver-
age acquisition delays are 1.92 seconds and 3.84 seconds.
The INQUIRY message is typically used for finding pub-
lic printers, faxes and similar equipment with an unknown ad-
dress. The INQUIRY message is very similar to the page mes-
sage but may require one additional train period to collect all
the responses.
If no data needs to be transmitted, the units may be put on
HOLD where only an internal timer is running. When units
go out of HOLD mode data transfer can be restarted instanta-
neously. Units may thus remain connected, without data trans-
fer, in a low power mode. The HOLD is typically used when
connecting several piconets. It could also be used for units
where data needs to be sent very infrequently and low power
consumption is important. A typical application would be a
room thermostat which may need to transfer data only once ev-
ery minute.
Two more low power modes are available, the SNIFF mode
and the PARK mode. If we list the modes in increasing order
of power efficiency, then the SNIFF mode has the higher duty
cycle, followed by the HOLD mode with a lower duty cycle,
and finishing with the PARK mode with the lowest duty cycle.
4 Mobile Computing and Communications Review, Volume 1, Number 2
Figure 3 describes the various possible connection states.
(unknown
address)
Page
(Known
address)
detach
Releases
Inquiry
Connecting
Active
Low Power
Unconnected
Standby
States
States
Models
Address
Member
Keeps Member Address
Connected
Park Hold Sniff
Transmit
data
Standby
Figure 3: Connection State Machine
E. Link types
Once a Bluetooth unit has been connected to a piconet it may
communicate by means of two link types. That is, between any
two members of the piconet forming a master-slave pair. Two
link types are supported. These links are:
 
Synchronous Connection Oriented (SCO) link
 
Asynchronous (or isochronous) Connectionless (ACL)
link.
Different link types may apply between different master-slave
pairs of the same piconet and the linktype may change arbitrar-
ily during a session. The link type defines what type of packets
can be used on a particular link. On each link type, 16 differ-
ent packet types can be used. The packets differ infunctionand
data bearing capabilities. For full duplex transmissions a Time
Division Duplex scheme is used. Each packet is transmitted in
a different hop channel than the previous packet.
An SCO link is a point-to-pointfull-duplexlink between the
master and a slave. This link is established once by the master
and kept alive untilbeing released by the master. The SCO link
is typically used for a voice connection. The master reserves
the slots used for the SCO link on the channel.
The ACL link makes a momentary connection between the
master and any of the slaves for the duration of one frame
(master-to-slave slot and slave-to-master slot). No slots are re-
served. The master can freely decide which slave to address
and in which order. The member subaddress in the packet
header determines the slave. A polling scheme is used to con-
trol the traffic from the slaves to the master. The link is in-
tended for asynchronous or isochronous data. However, if the
master uses this link to address the same slave at regular inter-
vals, it becomes a synchronous link. The ACL link supports
both symmetric and asymmetric modes. In addition, modes
have been defined with or without FEC, and with or without
CRC and ARQ.
F. Packet Definition
A packet (see Figure 4 consists of three fields: a 72-bit ac-
cess code, a 54-bit header, and a payload of variable length (2-
342 bytes). Packets may consist of the (shortened) access code
only, the access code and the header, or the access code, header
and payload.
PAYLOADACCESS CODE HEADER
16-27455472 MSBLSB
Figure 4: Typical packet format
The packet starts with a 72-bit channel access code. This ac-
cess code is used for synchronization, DC offset compensation
and identification. The access code identifies all packets ex-
changed on the channel of the piconet: all packets sent in the
same piconet are preceded by the same channel access code.
In the receiver of the Bluetooth unit, a sliding correlator cor-
relates against the access code and triggers when a threshold
is exceeded. This trigger signal is used to wake up the entire
signal processing of the receiver. In addition, it is used to fix
the receive timing. The correlator remains active during the
entire search window: when a new correlation value is found
which is larger than a previous correlation value which initially
triggered the receiver, the entire receiver is reset and triggered
again. The channel access code consists of a preamble, a sync
word, and a trailer, see Figure 5. Both preamble and trailer are
fixed bit patterns.
MSBLSB 4
TRAILER
34
464
SYNC WORDPREAMBLE
BRKRLAP
24 6
BCH
Figure 5: Channel Access Code
The preamble is a fixed zero-one pattern of 4 symbols used
to facilitate DC compensation. The sequence is either 1010 or
0101, depending on whether the LSB of the following access
code is 1 or 0 respectively. The sync word is a 64-bit code and
is derived from the master's lower address part (LAP) of its 48-
bit unique address. The code guarantees large Hamming dis-
tance between sync words based on different addresses. In ad-
dition, it has good auto- and cross-correlation properties which
improves the timing synchronization process. Like the pream-
ble, the trailer is a fixed zero-one pattern of four symbols used
for fine compensation. The sequence is either 1010 or 0101 de-
Mobile Computing and Communications Review, Volume 1, Number 2 5
pending on whether the MSB of the sync word is 0 or 1 respec-
tively.
M_ADDR TYPE
ARQN
HEC
3 4 1 1 1 8LSB MSB
FLOW SEQN
Figure 6: Header format
The header, shown in Figure 6, contains lower-level link
control information. It consist of 6 fields: a 3-bit sub ad-
dress (M ADDR), a 4-bitpacket type (TYPE), a 1-bitflow con-
trol bit (FLOW), a 1-bit acknowledge indication (ARQN), a 1-
bit sequence number (SEQN), and an 8-bit header error check
(HEC). The total header information consists of 18 bits, but is
protected with a 1/3 forward-error correction coding resulting
in a 54-bit header length.
M ADDR: This field represents a member address used to
distinguish the active participants on the piconet. With the
M ADDR, the master can separate the different slave active on
the piconet. This M ADDR is assigned temporarily to a unit
for the time it is active on the channel. Packets exchanged be-
tween the master and the active slave all carry the M ADDR
of this slave. The all-zero address is reserved for broadcast-
ing purposes. Slaves in the PARK mode are inactive but are
still locked to the FH channel. The parked slaves do not use an
M ADDR but their full 48-bit unique address.
TYPE: Sixteen different types of packets can be distin-
guished. The 4-bit TYPE code specifies which packet type is
used. Important to note is that the interpretation of the TYPE
code depends on the physical link type associated with the
packet. First, it shall be determined whether the packet is a
SCO or an ACL packet. Then, it shall be determined which
of the SCO packet types or ACL packet types we are dealing
with. The TYPE code also reveals how many slots the current
packet will occupy. This allows the non-addressed receivers to
go to sleep for the duration of the occupied slots.
FLOW: This bit is used for flow control over the ACL link.
When the RX buffer for the ACL connection in the recipient is
full and is not emptied by the link support unit, a STOP indi-
cation (FLOW=0) is returned to stop the transmission of data
temporarily. Note, that the STOP signal only concerns ACL
packets. Packets includingonlylinkcontrol (POLL and NULL
packets) or SCO packets can still be received. When the re-
ceive buffer is empty, a GO indication (FLOW=1) is returned.
When no packet is received or the received header is in error,
a GO is assumed implicitly.
ARQN: This is an acknowledge field to inform the sender
whether the reception of the packet in the preceding slot was
successful (ARQN=1) or unsuccessful (ARQN=0). When no
valid ARQN field is received, ARQN=0 is assumed implicitly.
ARQN=0 is the default value. The ARQN is piggy-backed in
the return packet. The success of the reception is checked by
means of a cyclic redundancy check (CRC) which is added to
each payload that contains data. An unnumbered ARQ scheme
is used which means that the ARQN relates to the packet just
received.
SEQN: This is a numbering field to distinguish new pack-
ets from retransmitted packets. The SEQN bit is toggled for
each new packet transmission. A retransmitted packet keeps
the same SEQN bit. If two consecutive packets are received
with the same SEQN bit, the second packet is ignored.
HEC: Each header has a header-error-check to check the
header integrity. The HEC consist of an 8-bit word generated
by the polynomial 647 (octal representation). Before generat-
ing the HEC, the HEC generator is initialized with the 8-bit
upper address part (UAP) of the master identity. The HEC is
then calculated over the 10 header bits. Before checking the
HEC, the receiver must initialize the HEC check circuitry with
the proper 8-bit UAP. If the HEC fails, the entire packet is dis-
carded.
G. Packet types
The 4-bitTYPE code in the packet header specifies 16 different
packet types. The packet types have been divided into 4 seg-
ments. The first segment consists of 4 packets and is reserved
for control packets common to all physical link types. The sec-
ond segment consists of 6 packets and is reserved for packets
occupying a single time slot. The third segment consists of 4
packets and is reserved for packets occupying three time slots.
The fourth segment consists of 2 packets and is reserved for
packets occupying five time slots. The slot occupancy is re-
flected in the segmentation and can directlybe derived from the
type code. Table 1 summarizes the packets defined for the SCO
and ACL link types.
At this moment, four different SCO packets have been de-
fined. So far, only single-slot packets have been defined. SCO
packets are typically used for synchronous information like
voice. The packets differ in the amount of FEC coding applied
and whether part of the packet is reserved for data as well as
voice. For the ACL link, 6 different packet types have been
defined. They differ in the in the amount of data carried, in the
presence of absence of FEC coding, and whether ARQ is ap-
plied or not.
H. Error correction
There are three error-correctionschemes defined for Bluetooth:
1/3 rate FEC, 2/3 rate FEC, and an ARQ scheme for data. The
purpose of the FEC scheme on the data payload is to reduce
the number of retransmissions. However, ina reasonable error-
free environment, FEC gives unnecessary overhead that re-
duces the throughput. Therefore, the packet definitions given
in Section G have been kept flexible to use FEC in the payload
or not, resulting in the DM and DH packets for the ACL link
and the HV packets for the SCO link. The packet header is al-
ways protected by a 1/3 rate FEC; it contains valuable link in-
formation and should survive more bit errors.
6 Mobile Computing and Communications Review, Volume 1, Number 2
Table 1: Packets defined for SCO and ACL link types
Segment TYPE SCO link ACL link
0000 NULL NULL
Control 0001 POLL POLL
Packets 0010 FHS FHS
0011 DM1 DM1
0100 DH1
Single 0101 HV1
Slot 0110 HV2
Packets 0111 HV3
1000 DV
1001 AUX1
1010 DM3
3-Slot 1011 DH3
Packets 1100
1101
5-Slot 1110 DM5
Packets 1111 DH5
I. Speech coding
In the Bluetooth system, two speech coding schemes are sup-
ported, Continuous Variable Slope Delta (CVSD) Modulation,
and logarithmic Pulse Coded Modulation (logPCM), both op-
eratingat 64 kbits/second. The defaultspeech coder is the more
robust CVSD coder.
The CVSD coder is a waveform coder applyinga delta mod-
ulation scheme[5]. To reduce slope-overload effects, syllabic
companding is applied: the delta step size is adapted accord-
ing to the average signal slope. The interface to the CVSD
speech coder is 8000 samples/second linear PCM. The CVSD
degrades gracefully in a noisy environment. Increasing inter-
ference is experienced as a growing background noise.
The alternative speech coding is basic logPCM. The 16-bit
linear PCM at 8000 samples/second is compressed to 8-bitlog-
PCM at 8000 samples/second using A-law or   -law compres-
sion.
J. Authentication and Privacy
In order to provide user protectionand informationsecrecy, the
system has to provide security measures both at the application
layer and the physical layer. These measures shall be appropri-
ate for a peer environment. This means that in each Bluetooth
unit, the authentication and encryption is implemented in the
same way. Bluetooth specifies a base level encryption, which
is well suited for silicon implementation, and an authentication
algorithm, which also provides devices which don't necessar-
ily have host processing capabilities a level of security. In ad-
dition, future ciphering algorithms can be supported in a back-
wards compatible way using version negotiation.
The main features are:
 
Challenge-response routine for authentication
 
Session key generation. Session keys can be changed at
any time during a connection
 
Stream-cipher
Table 2: Protection Entities
Entity Size
Bluetooth address 48 bits
private user key 64 bits
RAND 128 bites
In general security problems, three entities are used: a pub-
lic entity which is unique for each user, a secret entity, and a
random entity which is different for each new transaction. The
three entities and their sizes as used in Bluetooth are summa-
rized in Table 2.
The Bluetooth address is 48-bits in length and unique for
each Bluetooth unit. Bluetooth addresses are publicly known,
and can either be obtained via Man-Machine interactions
(MMI), or automatically via an inquiryroutine. The user key is
a 64-bit secret key which is derived during initialization but is
further never disclosed. The RAND is a random number which
willbe derived from a pseudo-random process in the Bluetooth
unit.
IV. Other Wireless Initiatives
This section describes the history and focus of several other
wireless industry groups and compares their vision and goals
to those of the Bluetooth SIG.
A. IrDA (http://www.irda.org/)
The Infrared Data Association (IrDA) is a non-profit corpora-
tion established in 1993 to set and support hardware and soft-
ware standards for infrared communication links. The IrDA
protocol stack is designed to support usage models similar to
those of Bluetooth. Legacy serial-cable-oriented applications
are supported via cable emulation while new IR-specific APIs
supportthe development of applications able to take advantage
of the full capabilities of the IR link management and trans-
portprotocols. There are already IrDA-compliantinterfaces on
many printers, handheld computers, notebook computers, and
digital still image cameras. The advantages of IR over RF in-
clude reduced cost, lower standby power, higher bandwidth,
and less regulations governing global use. The most signifi-
cant disadvantage of IR is the line-of-sightrestriction that con-
strains Bluetooth's vision of hidden and unconscious comput-
ing.
The Bluetooth SIG believes in promoting the development
of applications that work over either IR or RF. The applica-
tion developer, and especially the user, should not care what
physical medium is used. To achieve this, the Bluetooth SIG
is working on interfacing with the higher-level IrDA protocols
and has approached the IrDA to achieve interoperabilityacross
both wireless media.
B. IEEE 802.11 (http://www.ieee.org/)
The IEEE 802.11 standard defines RF and IR physical lay-
ers, Media Access Control (MAC) layer for LAN connectivity
and additional access point and security protocols. Generally
speaking, IEEE 802.11 defines a larger set of physical layers
Mobile Computing and Communications Review, Volume 1, Number 2 7
consisting of two radio solutions (frequency hopping and di-
rect sequence) and an IR solution while Bluetooth uses a fast
frequency hopping radio solution. Regarding the MAC layer,
Bluetooth uses a connection-oriented TDMA scheme while
IEEE 802.11 uses a carrier sense multiple access with collision
avoidance (CSMA/CA) scheme. The goal of IEEE 802.11 is
enabling LAN based applications with a larger radio coverage
while Bluetooth's paradigm is enabling wireless connectivity
between diverse types of devices including an access point to
a wired LAN in a piconet environment. Finally, IEEE 802.11
has been recently considering a short range solution similar to
the Bluetooth under its PAN working group.
C. HomeRF (http://www.homerf.org/)
The HomeRF
 
Working Group (HRFWG) is developing
an open specification targeting the home environment [6].
HomeRF focuses on both stand-alone and wireless extensions
to home networking technologies. In its current draft, the
HomeRF specification defines an air protocol based on a
combination of CSMA/CA for data and cordless telephony [1]
technology for voice. On the voice side, HomeRF uses an
ADPCM coding at 32 Kbps compared to Bluetooth's more
robust CVSD coding at 64 Kbps. However, HomeRF does
have the ability to retransmit a voice packet while Bluetooth
never retransmits voice. Another distinguishing factor is all
HomeRF voice traffic is channeled through a "control point"
while Bluetooth's voice traffic, like the data traffic, uses ad
hoc connections between any two Bluetoothunits. On the data
side, Bluetooth views HomeRF as a relaxed version of IEEE
802.11.
V. Summary
By developing the Specification for a low-cost, low-power
radio-based cable replacement, the Bluetooth SIG hopes to
drive an evolution in personal networking. In this article, we
have shared some of the vision, challenges, and architecture
the SIG is contemplating. For more information, readers are
encouraged to explore http://www.bluetooth.com.
By the time of this publication, the first release of the Blue-
tooth Specification (0.6) will be available to SIG members for
review and comments. The release of the Bluetooth Specifi-
cation 1.0 is planned for the first quarter in 1999 and products
compliant to that Specification are expected in late 1999.
Acknowledgements
The authors would like to thank all the people within the SIG
who have, and continueto, contributevaluable ideas, solutions,
and effort to move the Specification towards completion. The
authors would also like to thank Victor Bahl and SIGMOBILE
for the invitation to share the program with the research com-
munity, and the Bluetooth SIG program management for per-
mitting the publication of this article at this stage of the Speci-
fication . The name Bluetoothis inspired by the Danish Viking
King Harald Bluetooth (910-986), son of "Gorm the Old" and
father of "Sven Forkbeard". The codename is credited to Jim

Third party brands and names are the property of their respective owners.
Kardach (Intel) and the authors refer all name-related inquiries
to Jim for explanation.
References
[1] ETSI. Digital European Cordless Telephon Common Air
Interface, 1991.
[2] ETSI. Terminal Equipment to Mobile Station (TE-
MS) multiplexer protocol (GSM 07.10 version 6.1.0), July
1998. TS 101 369.
[3] IEEE. Standard for Wireless LAN Medium Access
Control (MAC) and Physical Layer (PHY) specifications,
1997.
[4] IRDA. IrDA Object Exchange Protocol (IrOBEX), Jan-
uary 1997.
[5] JAYANT, N., AND NOLL, P. DigitalCodingof Waveforms.
Prentice-Hall, 1984.
[6] NEGUS, K., ET AL., HomeRF and SWAP: Wireless Net-
working for the Connected Home. ACM Mobile Comput-
ing and Communications Review 2, 4 (October 1998).
Biographies
Jaap Haartsen received his M.S.E.E and Ph.D in 1986 and
1990, respectively, from the Delft University of Technology,
The Netherlands. In the past eight years, he worked in the re-
search departments of Ericsson in the US and in Sweden in the
area of wireless technology. Currently, he is located in The
Netherlands and chairs the Bluetooth SIG Air Protocol work-
ing group.
Mahmoud Naghshineh is with the IBM Thomas J. Watson
Research Center, Yorktown Heights, New York, where he cur-
rently manages the communication systems group. He has
been working at IBM since 1988 on a variety of research and
development projects dealing with design and analysis of com-
municationprotocols,and fast packet-switched/broadbandnet-
works, wireless and mobile ATM, wireless radio and infrared
access broadband and local area networks. He received his
doctoral degree from Columbia University, New York.
Jon Inouye in an engineering manager in Intel's Mobile Com-
munications Operations, part of the Mobile and Handheld
Products Group (MHPG), where his responsibilities include
chairing the Bluetooth SIG software working group.
Olaf J. Joeressen received the Dipl.-Ing. degree from Aachen
University of Technology (RWTH) in 1990. He received the
Dr.-Ing. degree from the RWTH in 1995 for work on the VLSI
implementationof Soft-OutputViterbi-Decoders. After that he
joined Nokia R&D in Bochum, Germany where he is now re-
sponsible for the Bluetooth core technology development.
Warren Allen is a Senior Product Planner at Toshiba Amer-
ica Information Systems, Inc. of Irvine, CA, where he has
been employed since 1989. He currently has responsibility for
discovering and integrating communications technologies into
Toshiba's product lines of portable, desktop and server com-
puters.
8 Mobile Computing and Communications Review, Volume 1, Number 2