DE1-SoC User Manual 1 www.terasic.com April 8, 2015 DE1-SoC User Manual 1 www.terasic.com April 8, 2015 CONTENTS CHAPTER 1 DE1-SOC DEVELOPMENT KIT .......................................................................... 4 1.1 Package Contents .......................................................................................................................4  1.2 DE1-SoC System CD.................................................................................................................5  1.3 Getting Help...............................................................................................................................5  CHAPTER 2 INTRODUCTION OF THE DE1-SOC BOARD..................................................... 6 2.1 Layout and Components.............................................................................................................6  2.2 Block Diagram of the DE1-SoC Board......................................................................................8  CHAPTER 3 USING THE DE1-SOC BOARD......................................................................... 12 3.1 Settings of FPGA Configuration Mode....................................................................................12  3.2 Configuration of Cyclone V SoC FPGA on DE1-SoC.............................................................13  3.3 Board Status Elements .............................................................................................................19  3.4 Board Reset Elements ..............................................................................................................20  3.5 Clock Circuitry.........................................................................................................................21  3.6 Peripherals Connected to the FPGA.........................................................................................23  3.6.1 User Push-buttons, Switches and LEDs................................................................................23  3.6.2 7-segment Displays ...............................................................................................................26  3.6.3 2x20 GPIO Expansion Headers.............................................................................................28  3.6.4 24-bit Audio CODEC............................................................................................................30  3.6.5 I2C Multiplexer.....................................................................................................................31  3.6.6 VGA ......................................................................................................................................32  3.6.7 TV Decoder...........................................................................................................................35  3.6.8 IR Receiver............................................................................................................................37  3.6.9 IR Emitter LED.....................................................................................................................37  DE1-SoC User Manual 2 www.terasic.com April 8, 2015 3.6.10 SDRAM Memory................................................................................................................38  3.6.11 PS/2 Serial Port ...................................................................................................................40  3.6.12 A/D Converter and 2x5 Header...........................................................................................42  3.7 Peripherals Connected to Hard Processor System (HPS).........................................................43  3.7.1 User Push-buttons and LEDs ................................................................................................43  3.7.2 Gigabit Ethernet ....................................................................................................................44  3.7.3 UART ....................................................................................................................................45  3.7.4 DDR3 Memory......................................................................................................................46  3.7.5 Micro SD Card Socket ..........................................................................................................48  3.7.6 2-port USB Host....................................................................................................................49  3.7.7 G-sensor ................................................................................................................................50  3.7.8 LTC Connector......................................................................................................................51  CHAPTER 4 DE1-SOC SYSTEM BUILDER........................................................................... 53 4.1 Introduction..............................................................................................................................53  4.2 Design Flow .............................................................................................................................53  4.3 Using DE1-SoC System Builder..............................................................................................54  CHAPTER 5 EXAMPLES FOR FPGA.................................................................................... 60 5.1 DE1-SoC Factory Configuration..............................................................................................60  5.2 Audio Recording and Playing ..................................................................................................61  5.3 Karaoke Machine .....................................................................................................................64  5.4 SDRAM Test in Nios II............................................................................................................66  5.5 SDRAM Test in Verilog ...........................................................................................................69  5.6 TV Box Demonstration ............................................................................................................71  5.7 PS/2 Mouse Demonstration......................................................................................................73  5.8 IR Emitter LED and Receiver Demonstration .........................................................................76  5.9 ADC Reading ...........................................................................................................................82  CHAPTER 6 EXAMPLES FOR HPS SOC ............................................................................... 85 DE1-SoC User Manual 3 www.terasic.com April 8, 2015 6.1 Hello Program ..........................................................................................................................85  6.2 Users LED and KEY................................................................................................................87  6.3 I2C Interfaced G-sensor ...........................................................................................................93  6.4 I2C MUX Test..........................................................................................................................96  CHAPTER 7 EXAMPLES FOR USING BOTH HPS SOC AND FGPA ..................................... 99 7.1 HPS Control LED and HEX.....................................................................................................99  7.2 DE1-SoC Control Panel .........................................................................................................103  7.3 DE1-SoC Linux Frame Buffer Project...................................................................................103  CHAPTER 8 PROGRAMMING THE EPCQ DEVICE............................................................. 105 8.1 Before Programming Begins..................................................................................................105  8.2 Convert .SOF File to .JIC File................................................................................................105  8.3 Write JIC File into the EPCQ Device.....................................................................................110  8.4 Erase the EPCQ Device.......................................................................................................... 111  8.5 Nios II Boot from EPCQ Device in Quartus II v13.1 ............................................................112  CHAPTER 9 APPENDIX........................................................................................................ 113 9.1 Revision History.....................................................................................................................113  9.2 Copyright Statement...............................................................................................................113  DE1-SoC User Manual 4 www.terasic.com April 8, 2015 Chapter 1 DE1-SoC Development Kit The DE1-SoC Development Kit presents a robust hardware design platform built around the Altera System-on-Chip (SoC) FPGA, which combines the latest dual-core Cortex-A9 embedded cores with industry-leading programmable logic for ultimate design flexibility. Users can now leverage the power of tremendous re-configurability paired with a high-performance, low-power processor system. Altera’s SoC integrates an ARM-based hard processor system (HPS) consisting of processor, peripherals and memory interfaces tied seamlessly with the FPGA fabric using a high-bandwidth interconnect backbone. The DE1-SoC development board is equipped with high-speed DDR3 memory, video and audio capabilities, Ethernet networking, and much more that promise many exciting applications. The DE1-SoC Development Kit contains all the tools needed to use the board in conjunction with a computer that runs the Microsoft Windows XP or later. 11..11 PPaacckkaaggee CCoonntteennttss Figure 1-1 shows a photograph of the DE1-SoC package. Figure 1-1 The DE1-SoC package contents DE1-SoC User Manual 5 www.terasic.com April 8, 2015 The DE1-SoC package includes:  The DE1-SoC development board  DE1-SoC Quick Start Guide  USB cable (Type A to B) for FPGA programming and control  USB cable (Type A to Mini-B) for UART control  12V DC power adapter 11..22 DDEE11--SSooCC SSyysstteemm CCDD The DE1-SoC System CD contains all the documents and supporting materials associated with DE1-SoC, including the user manual, system builder, reference designs, and device datasheets. Users can download this system CD from the link: http://cd-de1-soc.terasic.com. 11..33 GGeettttiinngg HHeellpp Here are the addresses where you can get help if you encounter any problems:  Altera Corporation  101 Innovation Drive San Jose, California, 95134 USA Email: university@altera.com  Terasic Technologies  9F., No.176, Sec.2, Gongdao 5th Rd, East Dist, Hsinchu City, 30070. Taiwan Email: support@terasic.com Tel.: +886-3-575-0880 Website: de1-soc.terasic.com DE1-SoC User Manual 6 www.terasic.com April 8, 2015 Chapter 2 Introduction of the DE1-SoC Board This chapter provides an introduction to the features and design characteristics of the board. 22..11 LLaayyoouutt aanndd CCoommppoonneennttss Figure 2-1 shows a photograph of the board. It depicts the layout of the board and indicates the location of the connectors and key components. DE1-SoC User Manual 7 www.terasic.com April 8, 2015 Figure 2-1 DE1-SoC development board (top view) Figure 2-2 De1-SoC development board (bottom view) The DE1-SoC board has many features that allow users to implement a wide range of designed circuits, from simple circuits to various multimedia projects. DE1-SoC User Manual 8 www.terasic.com April 8, 2015 The following hardware is provided on the board:  FPGA  Altera Cyclone® V SE 5CSEMA5F31C6N device  Altera serial configuration device – EPCQ256  USB-Blaster II onboard for programming; JTAG Mode  64MB SDRAM (16-bit data bus)  4 push-buttons  10 slide switches  10 red user LEDs  Six 7-segment displays  Four 50MHz clock sources from the clock generator  24-bit CD-quality audio CODEC with line-in, line-out, and microphone-in jacks  VGA DAC (8-bit high-speed triple DACs) with VGA-out connector  TV decoder (NTSC/PAL/SECAM) and TV-in connector  PS/2 mouse/keyboard connector  IR receiver and IR emitter  Two 40-pin expansion header with diode protection  A/D converter, 4-pin SPI interface with FPGA  HPS (Hard Processor System)  800MHz Dual-core ARM Cortex-A9 MPCore processor  1GB DDR3 SDRAM (32-bit data bus)  1 Gigabit Ethernet PHY with RJ45 connector  2-port USB Host, normal Type-A USB connector  Micro SD card socket  Accelerometer (I2C interface + interrupt)  UART to USB, USB Mini-B connector  Warm reset button and cold reset button  One user button and one user LED  LTC 2x7 expansion header 22..22 BBlloocckk DDiiaaggrraamm ooff tthhee DDEE11--SSooCC BBooaarrdd Figure 2-3 is the block diagram of the board. All the connections are established through the Cyclone V SoC FPGA device to provide maximum flexibility for users. Users can configure the FPGA to implement any system design. DE1-SoC User Manual 9 www.terasic.com April 8, 2015 Figure 2-3 Block diagram of DE1-SoC Detailed information about Figure 2-3 are listed below. FFPPGGAA DDeevviiccee  Cyclone V SoC 5CSEMA5F31 Device  Dual-core ARM Cortex-A9 (HPS)  85K programmable logic elements  4,450 Kbits embedded memory  6 fractional PLLs  2 hard memory controllers DE1-SoC User Manual 10 www.terasic.com April 8, 2015 CCoonnffiigguurraattiioonn aanndd DDeebbuugg  Quad serial configuration device – EPCQ256 on FPGA  Onboard USB-Blaster II (normal type B USB connector) MMeemmoorryy DDeevviiccee  64MB (32Mx16) SDRAM on FPGA  1GB (2x256Mx16) DDR3 SDRAM on HPS  Micro SD card socket on HPS CCoommmmuunniiccaattiioonn  Two port USB 2.0 Host (ULPI interface with USB type A connector)  UART to USB (USB Mini-B connector)  10/100/1000 Ethernet  PS/2 mouse/keyboard  IR emitter/receiver  I2C multiplexer CCoonnnneeccttoorrss  Two 40-pin expansion headers  One 10-pin ADC input header  One LTC connector (one Serial Peripheral Interface (SPI) Master ,one I2C and one GPIO interface ) DDiissppllaayy  24-bit VGA DAC AAuuddiioo  24-bit CODEC, Line-in, Line-out, and microphone-in jacks VViiddeeoo IInnppuutt  TV decoder (NTSC/PAL/SECAM) and TV-in connector DE1-SoC User Manual 11 www.terasic.com April 8, 2015 AADDCC  Fast throughput rate: 1 MSPS  Channel number: 8  Resolution: 12-bit  Analog input range : 0 ~ 2.5 V or 0 ~ 5V as selected via the RANGE bit in the control register SSwwiittcchheess,, BBuuttttoonnss,, aanndd IInnddiiccaattoorrss  5 user Keys (FPGA x4, HPS x1)  10 user switches (FPGA x10)  11 user LEDs (FPGA x10, HPS x 1)  2 HPS reset buttons (HPS_RESET_n and HPS_WARM_RST_n)  Six 7-segment displays SSeennssoorrss  G-Sensor on HPS PPoowweerr  12V DC input DE1-SoC User Manual 12 www.terasic.com April 8, 2015 Chapter 3 Using the DE1-SoC Board This chapter provides an instruction to use the board and describes the peripherals. 33..11 SSeettttiinnggss ooff FFPPGGAA CCoonnffiigguurraattiioonn MMooddee When the DE1-SoC board is powered on, the FPGA can be configured from EPCQ or HPS. The MSEL[4:0] pins are used to select the configuration scheme. It is implemented as a 6-pin DIP switch SW10 on the DE1-SoC board, as shown in Figure 3-1. Figure 3-1 DIP switch (SW10) setting of Active Serial (AS) mode at the back of DE1-SoC board Table 3-1 shows the relation between MSEL[4:0] and DIP switch (SW10). DE1-SoC User Manual 13 www.terasic.com April 8, 2015 Table 3-1 FPGA Configuration Mode Switch (SW10) Board Reference Signal Name Description Default SW10.1 MSEL0 Use these pins to set the FPGA Configuration scheme ON (“0”) SW10.2 MSEL1 OFF (“1”) SW10.3 MSEL2 ON (“0”) SW10.4 MSEL3 ON (“0”) SW10.5 MSEL4 OFF (“1”) SW10.6 N/A N/A N/A Figure 3-1 shows MSEL[4:0] setting of AS mode, which is also the default setting on DE1-SoC. When the board is powered on, the FPGA is configured from EPCQ, which is pre-programmed with the default code. If developers wish to reconfigure FPGA from an application software running on Linux, the MSEL[4:0] needs to be set to “01010” before the programming process begins. If developers using the "Linux Console with frame buffer" or "Linux LXDE Desktop" SD Card image, the MSEL[4:0] needs to be set to “00000” before the board is powered on. Table 3-2 MSEL Pin Settings for FPGA Configure of DE1-SoC MSEL[4:0] Configure Scheme Description 10010 AS FPGA configured from EPCQ (default) 01010 FPPx32 FPGA configured from HPS software: Linux 00000 FPPx16 FPGA configured from HPS software: U-Boot, with image stored on the SD card, like LXDE Desktop or console Linux with frame buffer edition. 33..22 CCoonnffiigguurraattiioonn ooff CCyycclloonnee VV SSooCC FFPPGGAA oonn DDEE11--SSooCC There are two types of programming method supported by DE1-SoC: 1. JTAG programming: It is named after the IEEE standards Joint Test Action Group. The configuration bit stream is downloaded directly into the Cyclone V SoC FPGA. The FPGA will retain its current status as long as the power keeps applying to the board; the configuration information will be lost when the power is off. 2. AS programming: The other programming method is Active Serial configuration. The configuration bit stream is downloaded into the quad serial configuration device (EPCQ256), which provides non-volatile storage for the bit stream. The information is retained within EPCQ256 DE1-SoC User Manual 14 www.terasic.com April 8, 2015 even if the DE1-SoC board is turned off. When the board is powered on, the configuration data in the EPCQ256 device is automatically loaded into the Cyclone V SoC FPGA.  JTAG Chain on DE1-SoC Board The FPGA device can be configured through JTAG interface on DE1-SoC board, but the JTAG chain must form a closed loop, which allows Quartus II programmer to the detect FPGA device. Figure 3-2 illustrates the JTAG chain on DE1-SoC board. Figure 3-2 Path of the JTAG chain  Configure the FPGA in JTAG Mode There are two devices (FPGA and HPS) on the JTAG chain. The following shows how the FPGA is programmed in JTAG mode step by step. 1. Open the Quartus II programmer and click “Auto Detect”, as circled in Figure 3-3 DE1-SoC User Manual 15 www.terasic.com April 8, 2015 Figure 3-3 Detect FPGA device in JTAG mode 2. Select detected device associated with the board, as circled in Figure 3-4. Figure 3-4 Select 5CSEMA5 device 3. Both FPGA and HPS are detected, as shown in Figure 3-5. DE1-SoC User Manual 16 www.terasic.com April 8, 2015 Figure 3-5 FPGA and HPS detected in Quartus programmer 4. Right click on the FPGA device and open the .sof file to be programmed, as highlighted in Figure 3-6. DE1-SoC User Manual 17 www.terasic.com April 8, 2015 Figure 3-6 Open the .sof file to be programmed into the FPGA device 5. Select the .sof file to be programmed, as shown in Figure 3-7. Figure 3-7 Select the .sof file to be programmed into the FPGA device DE1-SoC User Manual 18 www.terasic.com April 8, 2015 6. Click “Program/Configure” check box and then click “Start” button to download the .sof file into the FPGA device, as shown in Figure 3-8. Figure 3-8 Program .sof file into the FPGA device  Configure the FPGA in AS Mode  The DE1-SoC board uses a quad serial configuration device (EPCQ256) to store configuration data for the Cyclone V SoC FPGA. This configuration data is automatically loaded from the quad serial configuration device chip into the FPGA when the board is powered up.  Users need to use Serial Flash Loader (SFL) to program the quad serial configuration device via JTAG interface. The FPGA-based SFL is a soft intellectual property (IP) core within the FPGA that bridge the JTAG and Flash interfaces. The SFL Megafunction is available in Quartus II. Figure 3-9 shows the programming method when adopting SFL solution.  Please refer to Chapter 9: Steps of Programming the Quad Serial Configuration Device for the basic programming instruction on the serial configuration device. DE1-SoC User Manual 19 www.terasic.com April 8, 2015 Figure 3-9 Programming a quad serial configuration device with SFL solution 33..33 BBooaarrdd SSttaattuuss EElleemmeennttss In addition to the 10 LEDs that FPGA device can control, there are 5 indicators which can indicate the board status (See Figure 3-10), please refer the details in Table 3-3 Figure 3-10 LED Indicators on DE1-SoC DE1-SoC User Manual 20 www.terasic.com April 8, 2015 Table 3-3 LED Indicators Board Reference LED Name Description D14 12-V Power Illuminate when 12V power is active. TXD UART TXD Illuminate when data is transferred from FT232R to USB Host. RXD UART RXD Illuminate when data is transferred from USB Host to FT232R. D5 JTAG_RX Reserved D4 JTAG_TX 33..44 BBooaarrdd RReesseett EElleemmeennttss There are two HPS reset buttons on DE1-SoC, HPS (cold) reset and HPS warm reset, as shown in Figure 3-11. Table 3-4 describes the purpose of these two HPS reset buttons. Figure 3-12 is the reset tree for DE1-SoC. Figure 3-11 HPS cold reset and warm reset buttons on DE1-SoC DE1-SoC User Manual 21 www.terasic.com April 8, 2015 Table 3-4 Description of Two HPS Reset Buttons on DE1-SoC Board Reference Signal Name Description KEY5 HPS_RESET_N Cold reset to the HPS, Ethernet PHY and USB host device. Active low input which resets all HPS logics that can be reset. KEY7 HPS_WARM_RST_N Warm reset to the HPS block. Active low input affects the system reset domain for debug purpose. Figure 3-12 HPS reset tree on DE1-SoC board 33..55 CClloocckk CCiirrccuuiittrryy Figure 3-13 shows the default frequency of all external clocks to the Cyclone V SoC FPGA. A clock generator is used to distribute clock signals with low jitter. The four 50MHz clock signals connected to the FPGA are used as clock sources for user logic. One 25MHz clock signal is connected to two HPS clock inputs, and the other one is connected to the clock input of Gigabit DE1-SoC User Manual 22 www.terasic.com April 8, 2015 Ethernet Transceiver. Two 24MHz clock signals are connected to the clock inputs of USB Host/OTG PHY and USB hub controller. The associated pin assignment for clock inputs to FPGA I/O pins is listed in Table 3-5. Figure 3-13 Block diagram of the clock distribution on DE1-SoC Table 3-5 Pin Assignment of Clock Inputs Signal Name FPGA Pin No. Description I/O Standard CLOCK_50 PIN_AF14 50 MHz clock input 3.3V CLOCK2_50 PIN_AA16 50 MHz clock input 3.3V CLOCK3_50 PIN_Y26 50 MHz clock input 3.3V CLOCK4_50 PIN_K14 50 MHz clock input 3.3V HPS_CLOCK1_25 PIN_D25 25 MHz clock input 3.3V HPS_CLOCK2_25 PIN_F25 25 MHz clock input 3.3V DE1-SoC User Manual 23 www.terasic.com April 8, 2015 33..66 PPeerriipphheerraallss CCoonnnneecctteedd ttoo tthhee FFPPGGAA This section describes the interfaces connected to the FPGA. Users can control or monitor different interfaces with user logic from the FPGA. 3.6.1 User Push-buttons, Switches and LEDs The board has four push-buttons connected to the FPGA, as shown in Figure 3-14 Connections between the push-buttons and the Cyclone V SoC FPGA. Schmitt trigger circuit is implemented and act as switch debounce in Figure 3-15 for the push-buttons connected. The four push-buttons named KEY0, KEY1, KEY2, and KEY3 coming out of the Schmitt trigger device are connected directly to the Cyclone V SoC FPGA. The push-button generates a low logic level or high logic level when it is pressed or not, respectively. Since the push-buttons are debounced, they can be used as clock or reset inputs in a circuit. Figure 3-14 Connections between the push-buttons and the Cyclone V SoC FPGA DE1-SoC User Manual 24 www.terasic.com April 8, 2015 Pushbutton releasedPushbutton depressed Before Debouncing Schmitt Trigger Debounced Figure 3-15 Switch debouncing There are ten slide switches connected to the FPGA, as shown in Figure 3-16. These switches are not debounced and to be used as level-sensitive data inputs to a circuit. Each switch is connected directly and individually to the FPGA. When the switch is set to the DOWN position (towards the edge of the board), it generates a low logic level to the FPGA. When the switch is set to the UP position, a high logic level is generated to the FPGA. Figure 3-16 Connections between the slide switches and the Cyclone V SoC FPGA There are also ten user-controllable LEDs connected to the FPGA. Each LED is driven directly and individually by the Cyclone V SoC FPGA; driving its associated pin to a high logic level or low DE1-SoC User Manual 25 www.terasic.com April 8, 2015 level to turn the LED on or off, respectively. Figure 3-17 shows the connections between LEDs and Cyclone V SoC FPGA. Table 3-6, Table 3-7 and Table 3-8 list the pin assignment of user push-buttons, switches, and LEDs. Figure 3-17 Connections between the LEDs and the Cyclone V SoC FPGA Table 3-6 Pin Assignment of Slide Switches Signal Name FPGA Pin No. Description I/O Standard SW[0] PIN_AB12 Slide Switch[0] 3.3V SW[1] PIN_AC12 Slide Switch[1] 3.3V SW[2] PIN_AF9 Slide Switch[2] 3.3V SW[3] PIN_AF10 Slide Switch[3] 3.3V SW[4] PIN_AD11 Slide Switch[4] 3.3V SW[5] PIN_AD12 Slide Switch[5] 3.3V SW[6] PIN_AE11 Slide Switch[6] 3.3V SW[7] PIN_AC9 Slide Switch[7] 3.3V SW[8] PIN_AD10 Slide Switch[8] 3.3V SW[9] PIN_AE12 Slide Switch[9] 3.3V Table 3-7 Pin Assignment of Push-buttons Signal Name FPGA Pin No. Description I/O Standard KEY[0] PIN_AA14 Push-button[0] 3.3V KEY[1] PIN_AA15 Push-button[1] 3.3V KEY[2] PIN_W15 Push-button[2] 3.3V KEY[3] PIN_Y16 Push-button[3] 3.3V DE1-SoC User Manual 26 www.terasic.com April 8, 2015 Table 3-8 Pin Assignment of LEDs Signal Name FPGA Pin No. Description I/O Standard LEDR[0] PIN_V16 LED [0] 3.3V LEDR[1] PIN_W16 LED [1] 3.3V LEDR[2] PIN_V17 LED [2] 3.3V LEDR[3] PIN_V18 LED [3] 3.3V LEDR[4] PIN_W17 LED [4] 3.3V LEDR[5] PIN_W19 LED [5] 3.3V LEDR[6] PIN_Y19 LED [6] 3.3V LEDR[7] PIN_W20 LED [7] 3.3V LEDR[8] PIN_W21 LED [8] 3.3V LEDR[9] PIN_Y21 LED [9] 3.3V 3.6.2 7-segment Displays The DE1-SoC board has six 7-segment displays. These displays are paired to display numbers in various sizes. Figure 3-18 shows the connection of seven segments (common anode) to pins on Cyclone V SoC FPGA. The segment can be turned on or off by applying a low logic level or high logic level from the FPGA, respectively. Each segment in a display is indexed from 0 to 6, with corresponding positions given in Figure 3-18. Table 3-9 shows the pin assignment of FPGA to the 7-segment displays. Figure 3-18 Connections between the 7-segment display HEX0 and the Cyclone V SoC FPGA DE1-SoC User Manual 27 www.terasic.com April 8, 2015 Table 3-9 Pin Assignment of 7-segment Displays Signal Name FPGA Pin No. Description I/O Standard HEX0[0] PIN_AE26 Seven Segment Digit 0[0] 3.3V HEX0[1] PIN_AE27 Seven Segment Digit 0[1] 3.3V HEX0[2] PIN_AE28 Seven Segment Digit 0[2] 3.3V HEX0[3] PIN_AG27 Seven Segment Digit 0[3] 3.3V HEX0[4] PIN_AF28 Seven Segment Digit 0[4] 3.3V HEX0[5] PIN_AG28 Seven Segment Digit 0[5] 3.3V HEX0[6] PIN_AH28 Seven Segment Digit 0[6] 3.3V HEX1[0] PIN_AJ29 Seven Segment Digit 1[0] 3.3V HEX1[1] PIN_AH29 Seven Segment Digit 1[1] 3.3V HEX1[2] PIN_AH30 Seven Segment Digit 1[2] 3.3V HEX1[3] PIN_AG30 Seven Segment Digit 1[3] 3.3V HEX1[4] PIN_AF29 Seven Segment Digit 1[4] 3.3V HEX1[5] PIN_AF30 Seven Segment Digit 1[5] 3.3V HEX1[6] PIN_AD27 Seven Segment Digit 1[6] 3.3V HEX2[0] PIN_AB23 Seven Segment Digit 2[0] 3.3V HEX2[1] PIN_AE29 Seven Segment Digit 2[1] 3.3V HEX2[2] PIN_AD29 Seven Segment Digit 2[2] 3.3V HEX2[3] PIN_AC28 Seven Segment Digit 2[3] 3.3V HEX2[4] PIN_AD30 Seven Segment Digit 2[4] 3.3V HEX2[5] PIN_AC29 Seven Segment Digit 2[5] 3.3V HEX2[6] PIN_AC30 Seven Segment Digit 2[6] 3.3V HEX3[0] PIN_AD26 Seven Segment Digit 3[0] 3.3V HEX3[1] PIN_AC27 Seven Segment Digit 3[1] 3.3V HEX3[2] PIN_AD25 Seven Segment Digit 3[2] 3.3V HEX3[3] PIN_AC25 Seven Segment Digit 3[3] 3.3V HEX3[4] PIN_AB28 Seven Segment Digit 3[4] 3.3V HEX3[5] PIN_AB25 Seven Segment Digit 3[5] 3.3V HEX3[6] PIN_AB22 Seven Segment Digit 3[6] 3.3V HEX4[0] PIN_AA24 Seven Segment Digit 4[0] 3.3V HEX4[1] PIN_Y23 Seven Segment Digit 4[1] 3.3V HEX4[2] PIN_Y24 Seven Segment Digit 4[2] 3.3V HEX4[3] PIN_W22 Seven Segment Digit 4[3] 3.3V HEX4[4] PIN_W24 Seven Segment Digit 4[4] 3.3V HEX4[5] PIN_V23 Seven Segment Digit 4[5] 3.3V HEX4[6] PIN_W25 Seven Segment Digit 4[6] 3.3V HEX5[0] PIN_V25 Seven Segment Digit 5[0] 3.3V HEX5[1] PIN_AA28 Seven Segment Digit 5[1] 3.3V HEX5[2] PIN_Y27 Seven Segment Digit 5[2] 3.3V HEX5[3] PIN_AB27 Seven Segment Digit 5[3] 3.3V HEX5[4] PIN_AB26 Seven Segment Digit 5[4] 3.3V HEX5[5] PIN_AA26 Seven Segment Digit 5[5] 3.3V HEX5[6] PIN_AA25 Seven Segment Digit 5[6] 3.3V DE1-SoC User Manual 28 www.terasic.com April 8, 2015 3.6.3 2x20 GPIO Expansion Headers The board has two 40-pin expansion headers. Each header has 36 user pins connected directly to the Cyclone V SoC FPGA. It also comes with DC +5V (VCC5), DC +3.3V (VCC3P3), and two GND pins. The maximum power consumption allowed for a daughter card connected to one or two GPIO ports is shown in Table 3-10. Table 3-10 Voltage and Max. Current Limit of Expansion Header(s) Supplied Voltage Max. Current Limit 5V 1A 3.3V 1.5A Each pin on the expansion headers is connected to two diodes and a resistor for protection against high or low voltage level. Figure 3-19 shows the protection circuitry applied to all 2x36 data pins. Table 3-11 shows the pin assignment of two GPIO headers. Figure 3-19 Connections between the GPIO header and Cyclone V SoC FPGA Table 3-11 Pin Assignment of Expansion Headers Signal Name FPGA Pin No. Description I/O Standard GPIO_0[0] PIN_AC18 GPIO Connection 0[0] 3.3V GPIO_0 [1] PIN_Y17 GPIO Connection 0[1] 3.3V GPIO_0 [2] PIN_AD17 GPIO Connection 0[2] 3.3V GPIO_0 [3] PIN_Y18 GPIO Connection 0[3] 3.3V DE1-SoC User Manual 29 www.terasic.com April 8, 2015 GPIO_0 [4] PIN_AK16 GPIO Connection 0[4] 3.3V GPIO_0 [5] PIN_AK18 GPIO Connection 0[5] 3.3V GPIO_0 [6] PIN_AK19 GPIO Connection 0[6] 3.3V GPIO_0 [7] PIN_AJ19 GPIO Connection 0[7] 3.3V GPIO_0 [8] PIN_AJ17 GPIO Connection 0[8] 3.3V GPIO_0 [9] PIN_AJ16 GPIO Connection 0[9] 3.3V GPIO_0 [10] PIN_AH18 GPIO Connection 0[10] 3.3V GPIO_0 [11] PIN_AH17 GPIO Connection 0[11] 3.3V GPIO_0 [12] PIN_AG16 GPIO Connection 0[12] 3.3V GPIO_0 [13] PIN_AE16 GPIO Connection 0[13] 3.3V GPIO_0 [14] PIN_AF16 GPIO Connection 0[14] 3.3V GPIO_0 [15] PIN_AG17 GPIO Connection 0[15] 3.3V GPIO_0 [16] PIN_AA18 GPIO Connection 0[16] 3.3V GPIO_0 [17] PIN_AA19 GPIO Connection 0[17] 3.3V GPIO_0 [18] PIN_AE17 GPIO Connection 0[18] 3.3V GPIO_0 [19] PIN_AC20 GPIO Connection 0[19] 3.3V GPIO_0 [20] PIN_AH19 GPIO Connection 0[20] 3.3V GPIO_0 [21] PIN_AJ20 GPIO Connection 0[21] 3.3V GPIO_0 [22] PIN_AH20 GPIO Connection 0[22] 3.3V GPIO_0 [23] PIN_AK21 GPIO Connection 0[23] 3.3V GPIO_0 [24] PIN_AD19 GPIO Connection 0[24] 3.3V GPIO_0 [25] PIN_AD20 GPIO Connection 0[25] 3.3V GPIO_0 [26] PIN_AE18 GPIO Connection 0[26] 3.3V GPIO_0 [27] PIN_AE19 GPIO Connection 0[27] 3.3V GPIO_0 [28] PIN_AF20 GPIO Connection 0[28] 3.3V GPIO_0 [29] PIN_AF21 GPIO Connection 0[29] 3.3V GPIO_0 [30] PIN_AF19 GPIO Connection 0[30] 3.3V GPIO_0 [31] PIN_AG21 GPIO Connection 0[31] 3.3V GPIO_0 [32] PIN_AF18 GPIO Connection 0[32] 3.3V GPIO_0 [33] PIN_AG20 GPIO Connection 0[33] 3.3V GPIO_0 [34] PIN_AG18 GPIO Connection 0[34] 3.3V GPIO_0 [35] PIN_AJ21 GPIO Connection 0[35] 3.3V GPIO_1[0] PIN_AB17 GPIO Connection 1[0] 3.3V GPIO_1[1] PIN_AA21 GPIO Connection 1[1] 3.3V GPIO_1 [2] PIN_AB21 GPIO Connection 1[2] 3.3V GPIO_1 [3] PIN_AC23 GPIO Connection 1[3] 3.3V GPIO_1 [4] PIN_AD24 GPIO Connection 1[4] 3.3V GPIO_1 [5] PIN_AE23 GPIO Connection 1[5] 3.3V GPIO_1 [6] PIN_AE24 GPIO Connection 1[6] 3.3V GPIO_1 [7] PIN_AF25 GPIO Connection 1[7] 3.3V GPIO_1 [8] PIN_AF26 GPIO Connection 1[8] 3.3V GPIO_1 [9] PIN_AG25 GPIO Connection 1[9] 3.3V GPIO_1[10] PIN_AG26 GPIO Connection 1[10] 3.3V GPIO_1 [11] PIN_AH24 GPIO Connection 1[11] 3.3V DE1-SoC User Manual 30 www.terasic.com April 8, 2015 GPIO_1 [12] PIN_AH27 GPIO Connection 1[12] 3.3V GPIO_1 [13] PIN_AJ27 GPIO Connection 1[13] 3.3V GPIO_1 [14] PIN_AK29 GPIO Connection 1[14] 3.3V GPIO_1 [15] PIN_AK28 GPIO Connection 1[15] 3.3V GPIO_1 [16] PIN_AK27 GPIO Connection 1[16] 3.3V GPIO_1 [17] PIN_AJ26 GPIO Connection 1[17] 3.3V GPIO_1 [18] PIN_AK26 GPIO Connection 1[18] 3.3V GPIO_1 [19] PIN_AH25 GPIO Connection 1[19] 3.3V GPIO_1 [20] PIN_AJ25 GPIO Connection 1[20] 3.3V GPIO_1 [21] PIN_AJ24 GPIO Connection 1[21] 3.3V GPIO_1 [22] PIN_AK24 GPIO Connection 1[22] 3.3V GPIO_1 [23] PIN_AG23 GPIO Connection 1[23] 3.3V GPIO_1 [24] PIN_AK23 GPIO Connection 1[24] 3.3V GPIO_1 [25] PIN_AH23 GPIO Connection 1[25] 3.3V GPIO_1 [26] PIN_AK22 GPIO Connection 1[26] 3.3V GPIO_1 [27] PIN_AJ22 GPIO Connection 1[27] 3.3V GPIO_1 [28] PIN_AH22 GPIO Connection 1[28] 3.3V GPIO_1 [29] PIN_AG22 GPIO Connection 1[29] 3.3V GPIO_1 [30] PIN_AF24 GPIO Connection 1[30] 3.3V GPIO_1 [31] PIN_AF23 GPIO Connection 1[31] 3.3V GPIO_1 [32] PIN_AE22 GPIO Connection 1[32] 3.3V GPIO_1 [33] PIN_AD21 GPIO Connection 1[33] 3.3V GPIO_1 [34] PIN_AA20 GPIO Connection 1[34] 3.3V GPIO_1 [35] PIN_AC22 GPIO Connection 1[35] 3.3V 3.6.4 24-bit Audio CODEC The DE1-SoC board offers high-quality 24-bit audio via the Wolfson WM8731 audio CODEC (Encoder/Decoder). This chip supports microphone-in, line-in, and line-out ports, with adjustable sample rate from 8 kHz to 96 kHz. The WM8731 is controlled via serial I2C bus, which is connected to HPS or Cyclone V SoC FPGA through an I2C multiplexer. The connection of the audio circuitry to the FPGA is shown in Figure 3-20, and the associated pin assignment to the FPGA is listed in Table 3-12. More information about the WM8731 codec is available in its datasheet, which can be found on the manufacturer’s website, or in the directory \DE1_SOC_datasheets\Audio CODEC of DE1-SoC System CD. DE1-SoC User Manual 31 www.terasic.com April 8, 2015 Figure 3-20 Connections between the FPGA and audio CODEC Table 3-12 Pin Assignment of Audio CODEC Signal Name FPGA Pin No. Description I/O Standard AUD_ADCLRCK PIN_K8 Audio CODEC ADC LR Clock 3.3V AUD_ADCDAT PIN_K7 Audio CODEC ADC Data 3.3V AUD_DACLRCK PIN_H8 Audio CODEC DAC LR Clock 3.3V AUD_DACDAT PIN_J7 Audio CODEC DAC Data 3.3V AUD_XCK PIN_G7 Audio CODEC Chip Clock 3.3V AUD_BCLK PIN_H7 Audio CODEC Bit-stream Clock 3.3V I2C_SCLK PIN_J12 or PIN_E23 I2C Clock 3.3V I2C_SDAT PIN_K12 or PIN_C24 I2C Data 3.3V 3.6.5 I2C Multiplexer The DE1-SoC board implements an I2C multiplexer for HPS to access the I2C bus originally owned by FPGA. Figure 3-21 shows the connection of I2C multiplexer to the FPGA and HPS. HPS can access Audio CODEC and TV Decoder if and only if the HPS_I2C_CONTROL signal is set to high. The pin assignment of I2C bus is listed in Table 3-13 . DE1-SoC User Manual 32 www.terasic.com April 8, 2015 Figure 3-21 Control mechanism for the I2C multiplexer Table 3-13 Pin Assignment of I2C Bus Signal Name FPGA Pin No. Description I/O Standard FPGA_I2C_SCLK PIN_J12 FPGA I2C Clock 3.3V FPGA_I2C_SDAT PIN_K12 FPGA I2C Data 3.3V HPS_I2C1_SCLK PIN_E23 I2C Clock of the first HPS I2C concontroller 3.3V HPS_I2C1_SDAT PIN_C24 I2C Data of the first HPS I2C concontroller 3.3V HPS_I2C2_SCLK PIN_H23 I2C Clock of the second HPS I2C concontroller 3.3V HPS_I2C2_SDAT PIN_A25 I2C Data of the second HPS I2C concontroller 3.3V 3.6.6 VGA The DE1-SoC board has a 15-pin D-SUB connector populated for VGA output. The VGA synchronization signals are generated directly from the Cyclone V SoC FPGA, and the Analog Devices ADV7123 triple 10-bit high-speed video DAC (only the higher 8-bits are used) transforms signals from digital to analog to represent three fundamental colors (red, green, and blue). It can support up to SXGA standard (1280*1024) with signals transmitted at 100MHz. Figure 3-22 shows the signals connected between the FPGA and VGA. DE1-SoC User Manual 33 www.terasic.com April 8, 2015 Figure 3-22 Connections between the FPGA and VGA The timing specification for VGA synchronization and RGB (red, green, blue) data can be easily found on website nowadays. Figure 3-22 illustrates the basic timing requirements for each row (horizontal) displayed on a VGA monitor. An active-low pulse of specific duration is applied to the horizontal synchronization (hsync) input of the monitor, which signifies the end of one row of data and the start of the next. The data (RGB) output to the monitor must be off (driven to 0 V) for a time period called the back porch (b) after the hsync pulse occurs, which is followed by the display interval (c). During the data display interval the RGB data drives each pixel in turn across the row being displayed. Finally, there is a time period called the front porch (d) where the RGB signals must again be off before the next hsync pulse can occur. The timing of vertical synchronization (vsync) is similar to the one shown in Figure 3-23, except that a vsync pulse signifies the end of one frame and the start of the next, and the data refers to the set of rows in the frame (horizontal timing). Table 3-14 and Table 3-15 show different resolutions and durations of time period a, b, c, and d for both horizontal and vertical timing. More information about the ADV7123 video DAC is available in its datasheet, which can be found on the manufacturer’s website, or in the directory \Datasheets\VIDEO DAC of DE1-SoC System CD. The pin assignment between the Cyclone V SoC FPGA and the ADV7123 is listed in Table 3-16. DE1-SoC User Manual 34 www.terasic.com April 8, 2015 Figure 3-23 VGA horizontal timing specification Table 3-14 VGA Horizontal Timing Specification VGA mode Horizontal Timing Spec Configuration Resolution(HxV) a(us) b(us) c(us) d(us) Pixel clock(MHz) VGA(60Hz) 640x480 3.8 1.9 25.4 0.6 25 VGA(85Hz) 640x480 1.6 2.2 17.8 1.6 36 SVGA(60Hz) 800x600 3.2 2.2 20 1 40 SVGA(75Hz) 800x600 1.6 3.2 16.2 0.3 49 SVGA(85Hz) 800x600 1.1 2.7 14.2 0.6 56 XGA(60Hz) 1024x768 2.1 2.5 15.8 0.4 65 XGA(70Hz) 1024x768 1.8 1.9 13.7 0.3 75 XGA(85Hz) 1024x768 1.0 2.2 10.8 0.5 95 1280x1024(60Hz) 1280x1024 1.0 2.3 11.9 0.4 108 Table 3-15 VGA Vertical Timing Specification VGA mode Vertical Timing Spec Configuration Resolution(HxV) a(lines) b(lines) c(lines) d(lines) Pixel clock(MHz) VGA(60Hz) 640x480 2 33 480 10 25 VGA(85Hz) 640x480 3 25 480 1 36 SVGA(60Hz) 800x600 4 23 600 1 40 SVGA(75Hz) 800x600 3 21 600 1 49 SVGA(85Hz) 800x600 3 27 600 1 56 XGA(60Hz) 1024x768 6 29 768 3 65 XGA(70Hz) 1024x768 6 29 768 3 75 XGA(85Hz) 1024x768 3 36 768 1 95 1280x1024(60Hz) 1280x1024 3 38 1024 1 108 DE1-SoC User Manual 35 www.terasic.com April 8, 2015 Table 3-16 Pin Assignment of VGA Signal Name FPGA Pin No. Description I/O Standard VGA_R[0] PIN_A13 VGA Red[0] 3.3V VGA_R[1] PIN_C13 VGA Red[1] 3.3V VGA_R[2] PIN_E13 VGA Red[2] 3.3V VGA_R[3] PIN_B12 VGA Red[3] 3.3V VGA_R[4] PIN_C12 VGA Red[4] 3.3V VGA_R[5] PIN_D12 VGA Red[5] 3.3V VGA_R[6] PIN_E12 VGA Red[6] 3.3V VGA_R[7] PIN_F13 VGA Red[7] 3.3V VGA_G[0] PIN_J9 VGA Green[0] 3.3V VGA_G[1] PIN_J10 VGA Green[1] 3.3V VGA_G[2] PIN_H12 VGA Green[2] 3.3V VGA_G[3] PIN_G10 VGA Green[3] 3.3V VGA_G[4] PIN_G11 VGA Green[4] 3.3V VGA_G[5] PIN_G12 VGA Green[5] 3.3V VGA_G[6] PIN_F11 VGA Green[6] 3.3V VGA_G[7] PIN_E11 VGA Green[7] 3.3V VGA_B[0] PIN_B13 VGA Blue[0] 3.3V VGA_B[1] PIN_G13 VGA Blue[1] 3.3V VGA_B[2] PIN_H13 VGA Blue[2] 3.3V VGA_B[3] PIN_F14 VGA Blue[3] 3.3V VGA_B[4] PIN_H14 VGA Blue[4] 3.3V VGA_B[5] PIN_F15 VGA Blue[5] 3.3V VGA_B[6] PIN_G15 VGA Blue[6] 3.3V VGA_B[7] PIN_J14 VGA Blue[7] 3.3V VGA_CLK PIN_A11 VGA Clock 3.3V VGA_BLANK_N PIN_F10 VGA BLANK 3.3V VGA_HS PIN_B11 VGA H_SYNC 3.3V VGA_VS PIN_D11 VGA V_SYNC 3.3V VGA_SYNC_N PIN_C10 VGA SYNC 3.3V 3.6.7 TV Decoder The DE1-SoC board is equipped with an Analog Device ADV7180 TV decoder chip. The ADV7180 is an integrated video decoder which automatically detects and converts a standard analog baseband television signals (NTSC, PAL, and SECAM) into 4:2:2 component video data, which is compatible with the 8-bit ITU-R BT.656 interface standard. The ADV7180 is compatible with wide range of video devices, including DVD players, tape-based sources, broadcast sources, and security/surveillance cameras. DE1-SoC User Manual 36 www.terasic.com April 8, 2015 The registers in the TV decoder can be accessed and set through serial I2C bus by the Cyclone V SoC FPGA or HPS. Note that the I2C address W/R of the TV decoder (U4) is 0x40/0x41. The pin assignment of TV decoder is listed in Table 3-17. More information about the ADV7180 is available on the manufacturer’s website, or in the directory \DE1_SOC_datasheets\Video Decoder of DE1-SoC System CD. Figure 3-24 Connections between the FPGA and TV Decoder Table 3-17 Pin Assignment of TV Decoder Signal Name FPGA Pin No. Description I/O Standard TD_DATA [0] PIN_D2 TV Decoder Data[0] 3.3V TD_DATA [1] PIN_B1 TV Decoder Data[1] 3.3V TD_DATA [2] PIN_E2 TV Decoder Data[2] 3.3V TD_DATA [3] PIN_B2 TV Decoder Data[3] 3.3V TD_DATA [4] PIN_D1 TV Decoder Data[4] 3.3V TD_DATA [5] PIN_E1 TV Decoder Data[5] 3.3V TD_DATA [6] PIN_C2 TV Decoder Data[6] 3.3V TD_DATA [7] PIN_B3 TV Decoder Data[7] 3.3V TD_HS PIN_A5 TV Decoder H_SYNC 3.3V TD_VS PIN_A3 TV Decoder V_SYNC 3.3V TD_CLK27 PIN_H15 TV Decoder Clock Input. 3.3V TD_RESET_N PIN_F6 TV Decoder Reset 3.3V I2C_SCLK PIN_J12 or PIN_E23 I2C Clock 3.3V I2C_SDAT PIN_K12 or PIN_C24 I2C Data 3.3V DE1-SoC User Manual 37 www.terasic.com April 8, 2015 3.6.8 IR Receiver The board comes with an infrared remote-control receiver module (model: IRM-V538/TR1), whose datasheet is provided in the directory \Datasheets\ IR Receiver and Emitter of DE1-SoC system CD. The remote controller included in the kit has an encoding chip (uPD6121G) built-in for generating infrared signals. Figure 3-25 shows the connection of IR receiver to the FPGA. Table 3-18 shows the pin assignment of IR receiver to the FPGA. Figure 3-25 Connection between the FPGA and IR Receiver Table 3-18 Pin Assignment of IR Receiver Signal Name FPGA Pin No. Description I/O Standard IRDA_RXD PIN_ AA30 IR Receiver 3.3V 3.6.9 IR Emitter LED The board has an IR emitter LED for IR communication, which is widely used for operating television device wirelessly from a short line-of-sight distance. It can also be used to communicate with other systems by matching this IR emitter LED with another IR receiver on the other side. Figure 3-26 shows the connection of IR emitter LED to the FPGA. Table 3-19 shows the pin assignment of IR emitter LED to the FPGA. DE1-SoC User Manual 38 www.terasic.com April 8, 2015 Figure 3-26 Connection between the FPGA and IR emitter LED Table 3-19 Pin Assignment of IR Emitter LED Signal Name FPGA Pin No. Description I/O Standard IRDA_TXD PIN_ AB30 IR Emitter 3.3V 3.6.10 SDRAM Memory The board features 64MB of SDRAM with a single 64MB (32Mx16) SDRAM chip. The chip consists of 16-bit data line, control line, and address line connected to the FPGA. This chip uses the 3.3V LVCMOS signaling standard. Connections between the FPGA and SDRAM are shown in Figure 3-27, and the pin assignment is listed in Table 3-20. DE1-SoC User Manual 39 www.terasic.com April 8, 2015 Figure 3-27 Connections between the FPGA and SDRAM Table 3-20 Pin Assignment of SDRAM Signal Name FPGA Pin No. Description I/O Standard DRAM_ADDR[0] PIN_AK14 SDRAM Address[0] 3.3V DRAM_ADDR[1] PIN_AH14 SDRAM Address[1] 3.3V DRAM_ADDR[2] PIN_AG15 SDRAM Address[2] 3.3V DRAM_ADDR[3] PIN_AE14 SDRAM Address[3] 3.3V DRAM_ADDR[4] PIN_AB15 SDRAM Address[4] 3.3V DRAM_ADDR[5] PIN_AC14 SDRAM Address[5] 3.3V DRAM_ADDR[6] PIN_AD14 SDRAM Address[6] 3.3V DRAM_ADDR[7] PIN_AF15 SDRAM Address[7] 3.3V DRAM_ADDR[8] PIN_AH15 SDRAM Address[8] 3.3V DRAM_ADDR[9] PIN_AG13 SDRAM Address[9] 3.3V DRAM_ADDR[10] PIN_AG12 SDRAM Address[10] 3.3V DRAM_ADDR[11] PIN_AH13 SDRAM Address[11] 3.3V DRAM_ADDR[12] PIN_AJ14 SDRAM Address[12] 3.3V DRAM_DQ[0] PIN_AK6 SDRAM Data[0] 3.3V DRAM_DQ[1] PIN_AJ7 SDRAM Data[1] 3.3V DRAM_DQ[2] PIN_AK7 SDRAM Data[2] 3.3V DRAM_DQ[3] PIN_AK8 SDRAM Data[3] 3.3V DRAM_DQ[4] PIN_AK9 SDRAM Data[4] 3.3V DRAM_DQ[5] PIN_AG10 SDRAM Data[5] 3.3V DE1-SoC User Manual 40 www.terasic.com April 8, 2015 DRAM_DQ[6] PIN_AK11 SDRAM Data[6] 3.3V DRAM_DQ[7] PIN_AJ11 SDRAM Data[7] 3.3V DRAM_DQ[8] PIN_AH10 SDRAM Data[8] 3.3V DRAM_DQ[9] PIN_AJ10 SDRAM Data[9] 3.3V DRAM_DQ[10] PIN_AJ9 SDRAM Data[10] 3.3V DRAM_DQ[11] PIN_AH9 SDRAM Data[11] 3.3V DRAM_DQ[12] PIN_AH8 SDRAM Data[12] 3.3V DRAM_DQ[13] PIN_AH7 SDRAM Data[13] 3.3V DRAM_DQ[14] PIN_AJ6 SDRAM Data[14] 3.3V DRAM_DQ[15] PIN_AJ5 SDRAM Data[15] 3.3V DRAM_BA[0] PIN_AF13 SDRAM Bank Address[0] 3.3V DRAM_BA[1] PIN_AJ12 SDRAM Bank Address[1] 3.3V DRAM_LDQM PIN_AB13 SDRAM byte Data Mask[0] 3.3V DRAM_UDQM PIN_AK12 SDRAM byte Data Mask[1] 3.3V DRAM_RAS_N PIN_AE13 SDRAM Row Address Strobe 3.3V DRAM_CAS_N PIN_AF11 SDRAM Column Address Strobe 3.3V DRAM_CKE PIN_AK13 SDRAM Clock Enable 3.3V DRAM_CLK PIN_AH12 SDRAM Clock 3.3V DRAM_WE_N PIN_AA13 SDRAM Write Enable 3.3V DRAM_CS_N PIN_AG11 SDRAM Chip Select 3.3V 3.6.11 PS/2 Serial Port The DE1-SoC board comes with a standard PS/2 interface and a connector for a PS/2 keyboard or mouse. Figure 3-28 shows the connection of PS/2 circuit to the FPGA. Users can use the PS/2 keyboard and mouse on the DE1-SoC board simultaneously by a PS/2 Y-Cable, as shown in Figure 3-29. Instructions on how to use PS/2 mouse and/or keyboard can be found on various educational websites. The pin assignment associated to this interface is shown in Table 3-21. Note: If users connect only one PS/2 equipment, the PS/2 signals connected to the FPGA I/O should be “PS2_CLK” and “PS2_DAT”. DE1-SoC User Manual 41 www.terasic.com April 8, 2015 Figure 3-28 Connections between the FPGA and PS/2 Figure 3-29 Y-Cable for using keyboard and mouse simultaneously Table 3-21 Pin Assignment of PS/2 Signal Name FPGA Pin No. Description I/O Standard PS2_CLK PIN_AD7 PS/2 Clock 3.3V PS2_DAT PIN_AE7 PS/2 Data 3.3V PS2_CLK2 PIN_AD9 PS/2 Clock (reserved for second PS/2 device) 3.3V PS2_DAT2 PIN_AE9 PS/2 Data (reserved for second PS/2 device) 3.3V DE1-SoC User Manual 42 www.terasic.com April 8, 2015 3.6.12 A/D Converter and 2x5 Header The DE1-SoC has an analog-to-digital converter (AD7928), which features lower power, eight-channel CMOS 12-bit. This ADC offers conversion throughput rate up to 1MSPS. The analog input range for all input channels can be 0 V to 2.5 V or 0 V to 5V, depending on the RANGE bit in the control register. It can be configured to accept eight input signals at inputs ADC_IN0 through ADC_IN7. These eight input signals are connected to a 2x5 header, as shown in Figure 3-30. More information about the A/D converter chip is available in its datasheet. It can be found on manufacturer’s website or in the directory \datasheet of De1-SoC system CD. Figure 3-30 Signals of the 2x5 Header Figure 3-31 shows the connections between the FPGA, 2x5 header, and the A/D converter. DE1-SoC User Manual 43 www.terasic.com April 8, 2015 Figure 3-31 Connections between the FPGA, 2x5 header, and the A/D converter Table 3-22 Pin Assignment of ADC Signal Name FPGA Pin No. Description I/O Standard ADC_CS_N PIN_AJ4 Chip select 3.3V ADC_DOUT PIN_AK3 Digital data input 3.3V ADC_DIN PIN_AK4 Digital data output 3.3V ADC_SCLK PIN_AK2 Digital clock input 3.3V 33..77 PPeerriipphheerraallss CCoonnnneecctteedd ttoo HHaarrdd PPrroocceessssoorr SSyysstteemm ((HHPPSS)) This section introduces the interfaces connected to the HPS section of the Cyclone V SoC FPGA. Users can access these interfaces via the HPS processor. 33..77..11 UUsseerr PPuusshh--bbuuttttoonnss aanndd LLEEDDss Similar to the FPGA, the HPS also has its set of switches, buttons, LEDs, and other interfaces connected exclusively. Users can control these interfaces to monitor the status of HPS. Table 3-23 gives the pin assignment of all the LEDs, switches, and push-buttons. DE1-SoC User Manual 44 www.terasic.com April 8, 2015 Table 3-23 Pin Assignment of LEDs, Switches and Push-buttons Signal Name HPS GPIO Register/bit Function HPS_KEY GPIO54 GPIO1[25] I/O HPS_LED GPIO53 GPIO1[24] I/O 33..77..22 GGiiggaabbiitt EEtthheerrnneett The board supports Gigabit Ethernet transfer by an external Micrel KSZ9021RN PHY chip and HPS Ethernet MAC function. The KSZ9021RN chip with integrated 10/100/1000 Mbps Gigabit Ethernet transceiver also supports RGMII MAC interface. Figure 3-32 shows the connections between the HPS, Gigabit Ethernet PHY, and RJ-45 connector. The pin assignment associated to Gigabit Ethernet interface is listed in Table 3-24. More information about the KSZ9021RN PHY chip and its datasheet, as well as the application notes, which are available on the manufacturer’s website. Figure 3-32 Connections between the HPS and Gigabit Ethernet DE1-SoC User Manual 45 www.terasic.com April 8, 2015 Table 3-24 Pin Assignment of Gigabit Ethernet PHY Signal Name FPGA Pin No. Description I/O Standard HPS_ENET_TX_EN PIN_A20 GMII and MII transmit enable 3.3V HPS_ENET_TX_DATA[0] PIN_F20 MII transmit data[0] 3.3V HPS_ENET_TX_DATA[1] PIN_J19 MII transmit data[1] 3.3V HPS_ENET_TX_DATA[2] PIN_F21 MII transmit data[2] 3.3V HPS_ENET_TX_DATA[3] PIN_F19 MII transmit data[3] 3.3V HPS_ENET_RX_DV PIN_K17 GMII and MII receive data valid 3.3V HPS_ENET_RX_DATA[0] PIN_A21 GMII and MII receive data[0] 3.3V HPS_ENET_RX_DATA[1] PIN_B20 GMII and MII receive data[1] 3.3V HPS_ENET_RX_DATA[2] PIN_B18 GMII and MII receive data[2] 3.3V HPS_ENET_RX_DATA[3] PIN_D21 GMII and MII receive data[3] 3.3V HPS_ENET_RX_CLK PIN_G20 GMII and MII receive clock 3.3V HPS_ENET_RESET_N PIN_E18 Hardware Reset Signal 3.3V HPS_ENET_MDIO PIN_E21 Management Data 3.3V HPS_ENET_MDC PIN_B21 Management Data Clock Reference 3.3V HPS_ENET_INT_N PIN_C19 Interrupt Open Drain Output 3.3V HPS_ENET_GTX_CLK PIN_H19 GMII Transmit Clock 3.3V There are two LEDs, green LED (LEDG) and yellow LED (LEDY), which represent the status of Ethernet PHY (KSZ9021RNI). The LED control signals are connected to the LEDs on the RJ45 connector. The state and definition of LEDG and LEDY are listed in Table 3-25. For instance, the connection from board to Gigabit Ethernet is established once the LEDG lights on. Table 3-25 State and Definition of LED Mode Pins LED (State) LED (Definition) Link /Activity LEDG LEDY LEDG LEDY H H OFF OFF Link off L H ON OFF 1000 Link / No Activity Toggle H Blinking OFF 1000 Link / Activity (RX, TX) H L OFF ON 100 Link / No Activity H Toggle OFF Blinking 100 Link / Activity (RX, TX) L L ON ON 10 Link/ No Activity Toggle Toggle Blinking Blinking 10 Link / Activity (RX, TX) 33..77..33 UUAARRTT The board has one UART interface connected for communication with the HPS. This interface doesn’t support HW flow control signals. The physical interface is implemented by UART-USB onboard bridge from a FT232R chip to the host with an USB Mini-B connector. More information about the chip is available on the manufacturer’s website, or in the directory \Datasheets\UART TO DE1-SoC User Manual 46 www.terasic.com April 8, 2015 USB of DE1-SoC system CD. Figure 3-33 shows the connections between the HPS, FT232R chip, and the USB Mini-B connector. Table 3-26 lists the pin assignment of UART interface connected to the HPS. Figure 3-33 Connections between the HPS and FT232R Chip Table 3-26 Pin Assignment of UART Interface Signal Name FPGA Pin No. Description I/O Standard HPS_UART_RX PIN_B25 HPS UART Receiver 3.3V HPS_UART_TX PIN_C25 HPS UART Transmitter 3.3V HPS_CONV_USB_N PIN_B15 Reserve 3.3V 33..77..44 DDDDRR33 MMeemmoorryy The DDR3 devices connected to the HPS are the exact same model as the ones connected to the FPGA. The capacity is 1GB and the data bandwidth is in 32-bit, comprised of two x16 devices with a single address/command bus. The signals are connected to the dedicated Hard Memory Controller for HPS I/O banks and the target speed is 400 MHz. Table 3-27 lists the pin assignment of DDR3 and its description with I/O standard. Table 3-27 Pin Assignment of DDR3 Memory Signal Name FPGA Pin No. Description I/O Standard HPS_DDR3_A[0] PIN_F26 HPS DDR3 Address[0] SSTL-15 Class I HPS_DDR3_A[1] PIN_G30 HPS DDR3 Address[1] SSTL-15 Class I HPS_DDR3_A[2] PIN_F28 HPS DDR3 Address[2] SSTL-15 Class I HPS_DDR3_A[3] PIN_F30 HPS DDR3 Address[3] SSTL-15 Class I HPS_DDR3_A[4] PIN_J25 HPS DDR3 Address[4] SSTL-15 Class I HPS_DDR3_A[5] PIN_J27 HPS DDR3 Address[5] SSTL-15 Class I DE1-SoC User Manual 47 www.terasic.com April 8, 2015 HPS_DDR3_A[6] PIN_F29 HPS DDR3 Address[6] SSTL-15 Class I HPS_DDR3_A[7] PIN_E28 HPS DDR3 Address[7] SSTL-15 Class I HPS_DDR3_A[8] PIN_H27 HPS DDR3 Address[8] SSTL-15 Class I HPS_DDR3_A[9] PIN_G26 HPS DDR3 Address[9] SSTL-15 Class I HPS_DDR3_A[10] PIN_D29 HPS DDR3 Address[10] SSTL-15 Class I HPS_DDR3_A[11] PIN_C30 HPS DDR3 Address[11] SSTL-15 Class I HPS_DDR3_A[12] PIN_B30 HPS DDR3 Address[12] SSTL-15 Class I HPS_DDR3_A[13] PIN_C29 HPS DDR3 Address[13] SSTL-15 Class I HPS_DDR3_A[14] PIN_H25 HPS DDR3 Address[14] SSTL-15 Class I HPS_DDR3_BA[0] PIN_E29 HPS DDR3 Bank Address[0] SSTL-15 Class I HPS_DDR3_BA[1] PIN_J24 HPS DDR3 Bank Address[1] SSTL-15 Class I HPS_DDR3_BA[2] PIN_J23 HPS DDR3 Bank Address[2] SSTL-15 Class I HPS_DDR3_CAS_n PIN_E27 DDR3 Column Address Strobe SSTL-15 Class I HPS_DDR3_CKE PIN_L29 HPS DDR3 Clock Enable SSTL-15 Class I HPS_DDR3_CK_n PIN_L23 HPS DDR3 Clock Differential 1.5-V SSTL Class I HPS_DDR3_CK_p PIN_M23 HPS DDR3 Clock p Differential 1.5-V SSTL Class I HPS_DDR3_CS_n PIN_H24 HPS DDR3 Chip Select SSTL-15 Class I HPS_DDR3_DM[0] PIN_K28 HPS DDR3 Data Mask[0] SSTL-15 Class I HPS_DDR3_DM[1] PIN_M28 HPS DDR3 Data Mask[1] SSTL-15 Class I HPS_DDR3_DM[2] PIN_R28 HPS DDR3 Data Mask[2] SSTL-15 Class I HPS_DDR3_DM[3] PIN_W30 HPS DDR3 Data Mask[3] SSTL-15 Class I HPS_DDR3_DQ[0] PIN_K23 HPS DDR3 Data[0] SSTL-15 Class I HPS_DDR3_DQ[1] PIN_K22 HPS DDR3 Data[1] SSTL-15 Class I HPS_DDR3_DQ[2] PIN_H30 HPS DDR3 Data[2] SSTL-15 Class I HPS_DDR3_DQ[3] PIN_G28 HPS DDR3 Data[3] SSTL-15 Class I HPS_DDR3_DQ[4] PIN_L25 HPS DDR3 Data[4] SSTL-15 Class I HPS_DDR3_DQ[5] PIN_L24 HPS DDR3 Data[5] SSTL-15 Class I HPS_DDR3_DQ[6] PIN_J30 HPS DDR3 Data[6] SSTL-15 Class I HPS_DDR3_DQ[7] PIN_J29 HPS DDR3 Data[7] SSTL-15 Class I HPS_DDR3_DQ[8] PIN_K26 HPS DDR3 Data[8] SSTL-15 Class I HPS_DDR3_DQ[9] PIN_L26 HPS DDR3 Data[9] SSTL-15 Class I HPS_DDR3_DQ[10] PIN_K29 HPS DDR3 Data[10] SSTL-15 Class I HPS_DDR3_DQ[11] PIN_K27 HPS DDR3 Data[11] SSTL-15 Class I HPS_DDR3_DQ[12] PIN_M26 HPS DDR3 Data[12] SSTL-15 Class I HPS_DDR3_DQ[13] PIN_M27 HPS DDR3 Data[13] SSTL-15 Class I HPS_DDR3_DQ[14] PIN_L28 HPS DDR3 Data[14] SSTL-15 Class I HPS_DDR3_DQ[15] PIN_M30 HPS DDR3 Data[15] SSTL-15 Class I HPS_DDR3_DQ[16] PIN_U26 HPS DDR3 Data[16] SSTL-15 Class I HPS_DDR3_DQ[17] PIN_T26 HPS DDR3 Data[17] SSTL-15 Class I HPS_DDR3_DQ[18] PIN_N29 HPS DDR3 Data[18] SSTL-15 Class I HPS_DDR3_DQ[19] PIN_N28 HPS DDR3 Data[19] SSTL-15 Class I HPS_DDR3_DQ[20] PIN_P26 HPS DDR3 Data[20] SSTL-15 Class I HPS_DDR3_DQ[21] PIN_P27 HPS DDR3 Data[21] SSTL-15 Class I HPS_DDR3_DQ[22] PIN_N27 HPS DDR3 Data[22] SSTL-15 Class I DE1-SoC User Manual 48 www.terasic.com April 8, 2015 HPS_DDR3_DQ[23] PIN_R29 HPS DDR3 Data[23] SSTL-15 Class I HPS_DDR3_DQ[24] PIN_P24 HPS DDR3 Data[24] SSTL-15 Class I HPS_DDR3_DQ[25] PIN_P25 HPS DDR3 Data[25] SSTL-15 Class I HPS_DDR3_DQ[26] PIN_T29 HPS DDR3 Data[26] SSTL-15 Class I HPS_DDR3_DQ[27] PIN_T28 HPS DDR3 Data[27] SSTL-15 Class I HPS_DDR3_DQ[28] PIN_R27 HPS DDR3 Data[28] SSTL-15 Class I HPS_DDR3_DQ[29] PIN_R26 HPS DDR3 Data[29] SSTL-15 Class I HPS_DDR3_DQ[30] PIN_V30 HPS DDR3 Data[30] SSTL-15 Class I HPS_DDR3_DQ[31] PIN_W29 HPS DDR3 Data[31] SSTL-15 Class I HPS_DDR3_DQS_n[0] PIN_M19 HPS DDR3 Data Strobe n[0] Differential 1.5-V SSTL Class I HPS_DDR3_DQS_n[1] PIN_N24 HPS DDR3 Data Strobe n[1] Differential 1.5-V SSTL Class I HPS_DDR3_DQS_n[2] PIN_R18 HPS DDR3 Data Strobe n[2] Differential 1.5-V SSTL Class I HPS_DDR3_DQS_n[3] PIN_R21 HPS DDR3 Data Strobe n[3] Differential 1.5-V SSTL Class I HPS_DDR3_DQS_p[0] PIN_N18 HPS DDR3 Data Strobe p[0] Differential 1.5-V SSTL Class I HPS_DDR3_DQS_p[1] PIN_N25 HPS DDR3 Data Strobe p[1] Differential 1.5-V SSTL Class I HPS_DDR3_DQS_p[2] PIN_R19 HPS DDR3 Data Strobe p[2] Differential 1.5-V SSTL Class I HPS_DDR3_DQS_p[3] PIN_R22 HPS DDR3 Data Strobe p[3] Differential 1.5-V SSTL Class I HPS_DDR3_ODT PIN_H28 HPS DDR3 On-die Termination SSTL-15 Class I HPS_DDR3_RAS_n PIN_D30 DDR3 Row Address Strobe SSTL-15 Class I HPS_DDR3_RESET_n PIN_P30 HPS DDR3 Reset SSTL-15 Class I HPS_DDR3_WE_n PIN_C28 HPS DDR3 Write Enable SSTL-15 Class I HPS_DDR3_RZQ PIN_D27 External reference ball for output drive calibration 1.5 V 33..77..55 MMiiccrroo SSDD CCaarrdd SSoocckkeett The board supports Micro SD card interface with x4 data lines. It serves not only an external storage for the HPS, but also an alternative boot option for DE1-SoC board. Figure 3-34 shows signals connected between the HPS and Micro SD card socket. Table 3-28 lists the pin assignment of Micro SD card socket to the HPS. DE1-SoC User Manual 49 www.terasic.com April 8, 2015 Figure 3-34 Connections between the FPGA and SD card socket Table 3-28 Pin Assignment of Micro SD Card Socket Signal Name FPGA Pin No. Description I/O Standard HPS_SD_CLK PIN_A16 HPS SD Clock 3.3V HPS_SD_CMD PIN_F18 HPS SD Command Line 3.3V HPS_SD_DATA[0] PIN_G18 HPS SD Data[0] 3.3V HPS_SD_DATA[1] PIN_C17 HPS SD Data[1] 3.3V HPS_SD_DATA[2] PIN_D17 HPS SD Data[2] 3.3V HPS_SD_DATA[3] PIN_B16 HPS SD Data[3] 3.3V 33..77..66 22--ppoorrtt UUSSBB HHoosstt The board has two USB 2.0 type-A ports with a SMSC USB3300 controller and a 2-port hub controller. The SMSC USB3300 device in 32-pin QFN package interfaces with the SMSC USB2512B hub controller. This device supports UTMI+ Low Pin Interface (ULPI), which communicates with the USB 2.0 controller in HPS. The PHY operates in Host mode by connecting the ID pin of USB3300 to ground. When operating in Host mode, the device is powered by the two USB type-A ports. Figure 3-35 shows the connections of USB PTG PHY to the HPS. Table 3-29 lists the pin assignment of USBOTG PHY to the HPS. DE1-SoC User Manual 50 www.terasic.com April 8, 2015 Figure 3-35 Connections between the HPS and USB OTG PHY Table 3-29 Pin Assignment of USB OTG PHY Signal Name FPGA Pin No. Description I/O Standard HPS_USB_CLKOUT PIN_N16 60MHz Reference Clock Output 3.3V HPS_USB_DATA[0] PIN_E16 HPS USB_DATA[0] 3.3V HPS_USB_DATA[1] PIN_G16 HPS USB_DATA[1] 3.3V HPS_USB_DATA[2] PIN_D16 HPS USB_DATA[2] 3.3V HPS_USB_DATA[3] PIN_D14 HPS USB_DATA[3] 3.3V HPS_USB_DATA[4] PIN_A15 HPS USB_DATA[4] 3.3V HPS_USB_DATA[5] PIN_C14 HPS USB_DATA[5] 3.3V HPS_USB_DATA[6] PIN_D15 HPS USB_DATA[6] 3.3V HPS_USB_DATA[7] PIN_M17 HPS USB_DATA[7] 3.3V HPS_USB_DIR PIN_E14 Direction of the Data Bus 3.3V HPS_USB_NXT PIN_A14 Throttle the Data 3.3V HPS_USB_RESET PIN_G17 HPS USB PHY Reset 3.3V HPS_USB_STP PIN_C15 Stop Data Stream on the Bus 3.3V 33..77..77 GG--sseennssoorr The board comes with a digital accelerometer sensor module (ADXL345), commonly known as G-sensor. This G-sensor is a small, thin, ultralow power assumption 3-axis accelerometer with high-resolution measurement. Digitalized output is formatted as 16-bit in two’s complement and can be accessed through I2C interface. The I2C address of G-sensor is 0xA6/0xA7. More information about this chip can be found in its datasheet, which is available on manufacturer’s website or in the directory \Datasheet folder of DE1-SoC system CD. Figure 3-36 shows the connections between the HPS and G-sensor. Table 3-30 lists the pin assignment of G-senor to the HPS. DE1-SoC User Manual 51 www.terasic.com April 8, 2015 Figure 3-36 Connections between Cyclone V SoC FPGA and G-Sensor Table 3-30 Pin Assignment of G-senor Signal Name FPGA Pin No. Description I/O Standard HPS_GSENSOR_INT PIN_B22 HPS GSENSOR Interrupt Output 3.3V HPS_I2C1_SCLK PIN_E23 HPS I2C Clock (share bus with LTC) 3.3V HPS_I2C1_SDAT PIN_C24 HPS I2C Data (share bus) 3.3V 33..77..88 LLTTCC CCoonnnneeccttoorr The board has a 14-pin header, which is originally used to communicate with various daughter cards from Linear Technology. It is connected to the SPI Master and I2C ports of HPS. The communication with these two protocols is bi-directional. The 14-pin header can also be used for GPIO, SPI, or I2C based communication with the HPS. Connections between the HPS and LTC connector are shown in Figure 3-37, and the pin assignment of LTC connector is listed in Table 3-31. DE1-SoC User Manual 52 www.terasic.com April 8, 2015 Figure 3-37 Connections between the HPS and LTC connector Table 3-31 Pin Assignment of LTC Connector Signal Name FPGA Pin No. Description I/O Standard HPS_LTC_GPIO PIN_H17 HPS LTC GPIO 3.3V HPS_I2C2_SCLK PIN_H23 HPS I2C2 Clock (share bus with G-Sensor) 3.3V HPS_I2C2_SDAT PIN_A25 HPS I2C2 Data (share bus with G-Sensor) 3.3V HPS_SPIM_CLK PIN_C23 SPI Clock 3.3V HPS_SPIM_MISO PIN_E24 SPI Master Input/Slave Output 3.3V HPS_SPIM_MOSI PIN_D22 SPI Master Output /Slave Input 3.3V HPS_SPIM_SS PIN_D24 SPI Slave Select 3.3V DE1-SoC User Manual 53 www.terasic.com April 8, 2015 Chapter 4 DE1-SoC System Builder This chapter describes how users can create a custom design project with the tool named DE1-SoC System Builder. 44..11 IInnttrroodduuccttiioonn The DE1-SoC System Builder is a Windows-based utility. It is designed to help users create a Quartus II project for DE1-SoC within minutes. The generated Quartus II project files include:  Quartus II project file (.qpf)  Quartus II setting file (.qsf)  Top-level design file (.v)  Synopsis design constraints file (.sdc)  Pin assignment document (.htm) The above files generated by the DE1-SoC System Builder can also prevent occurrence of situations that are prone to compilation error when users manually edit the top-level design file or place pin assignment. The common mistakes that users encounter are:  Board is damaged due to incorrect bank voltage setting or pin assignment.  Board is malfunctioned because of wrong device chosen, declaration of pin location or direction is incorrect or forgotten.  Performance degradation due to improper pin assignment. 44..22 DDeessiiggnn FFllooww This section provides an introduction to the design flow of building a Quartus II project for DE1-SoC under the DE1-SoC System Builder. The design flow is illustrated in Figure 4-1. DE1-SoC User Manual 54 www.terasic.com April 8, 2015 The DE1-SoC System Builder will generate two major files, a top-level design file (.v) and a Quartus II setting file (.qsf) after users launch the DE1-SoC System Builder and create a new project according to their design requirements The top-level design file contains a top-level Verilog HDL wrapper for users to add their own design/logic. The Quartus II setting file contains information such as FPGA device type, top-level pin assignment, and the I/O standard for each user-defined I/O pin. Finally, the Quartus II programmer is used to download .sof file to the development board via JTAG interface. Figure 4-1 Design flow of building a project from the beginning to the end 44..33 UUssiinngg DDEE11--SSooCC SSyysstteemm BBuuiillddeerr This section provides the procedures in details on how to use the DE1-SoC System Builder. DE1-SoC User Manual 55 www.terasic.com April 8, 2015  Install and Launch the DE1-SoC System Builder The DE1-SoC System Builder is located in the directory: “Tools\SystemBuilder” of the DE1-SoC System CD. Users can copy the entire folder to a host computer without installing the utility. A window will pop up, as shown in Figure 4-2, after executing the DE1-SoC SystemBuilder.exe on the host computer. Figure 4-2 The GUI of DE1-SoC System Builder  Enter Project Name Enter the project name in the circled area, as shown in Figure 4-3. The project name typed in will be assigned automatically as the name of your top-level design entity. DE1-SoC User Manual 56 www.terasic.com April 8, 2015 Figure 4-3 Enter the project name  System Configuration Users are given the flexibility in the System Configuration to include their choice of components in the project, as shown in Figure 4-4. Each component onboard is listed and users can enable or disable one or more components at will. If a component is enabled, the DE1-SoC System Builder will automatically generate its associated pin assignment, including the pin name, pin location, pin direction, and I/O standard. DE1-SoC User Manual 57 www.terasic.com April 8, 2015 Figure 4-4 System configuration group  GPIO Expansion If users connect any Terasic GPIO-based daughter card to the GPIO connector(s) on DE1-SoC, the DE1-SoC System Builder can generate a project that include the corresponding module, as shown in Figure 4-5. It will also generate the associated pin assignment automatically, including pin name, pin location, pin direction, and I/O standard. DE1-SoC User Manual 58 www.terasic.com April 8, 2015 Figure 4-5 GPIO expansion group The “Prefix Name” is an optional feature that denote the pin name of the daughter card assigned in your design. Users may leave this field blank.  Project Setting Management The DE1-SoC System Builder also provides the option to load a setting or save users’ current board configuration in .cfg file, as shown in Figure 4-6. DE1-SoC User Manual 59 www.terasic.com April 8, 2015 Figure 4-6 Project Settings  Project Generation When users press the Generate button, the DE1-SoC System Builder will generate the corresponding Quartus II files and documents, as listed in Table 4-1: Table 4-1 Files generated by the DE1-SoC System Builder No. Filename Description 1 .v Top level Verilog HDL file for Quartus II 2 .qpf Quartus II Project File 3 .qsf Quartus II Setting File 4 .sdc Synopsis Design Constraints file for Quartus II 5 .htm Pin Assignment Document Users can add custom logic into the project in Quartus II and compile the project to generate the SRAM Object File (.sof). DE1-SoC User Manual 60 www.terasic.com April 8, 2015 Chapter 5 Examples For FPGA This chapter provides examples of advanced designs implemented by RTL or Qsys on the DE1-SoC board. These reference designs cover the features of peripherals connected to the FPGA, such as audio, SDRAM, and IR receiver. All the associated files can be found in the directory \Demonstrations\FPGA of DE1-SoC System CD.  Installation of Demonstrations To install the demonstrations on your computer: Copy the folder Demonstrations to a local directory of your choice. It is important to make sure the path to your local directory contains NO space. Otherwise it will lead to error in Nios II. Note Quartus II v13.0 or later is required for all DE1-SoC demonstrations to support Cyclone V SoC device. 55..11 DDEE11--SSooCC FFaaccttoorryy CCoonnffiigguurraattiioonn The DE1-SoC board has a default configuration bit-stream pre-programmed, which demonstrates some of the basic features onboard. The setup required for this demonstration and the location of its files are shown below.  Demonstration Setup, File Locations, and Instructions  Project directory: DE1_SoC_Default  Bitstream used: DE1_SoC_Default.sof or DE1_SoC_Default.jic  Power on the DE1-SoC board with the USB cable connected to the USB-Blaster II port. If necessary (that is, if the default factory configuration is not currently stored in the EPCQ device), download the bit stream to the board via JTAG interface.  You should now be able to observe the 7-segment displays are showing a sequence of characters, and the red LEDs are blinking. DE1-SoC User Manual 61 www.terasic.com April 8, 2015  If the VGA D-SUB connector is connected to a VGA display, it would show a color picture.  If the stereo line-out jack is connected to a speaker and KEY[1] is pressed, a 1 kHz humming sound will come out of the line-out port .  For the ease of execution, a demo_batch folder is provided in the project. It is able to not only load the bit stream into the FPGA in command line, but also program or erase .jic file to the EPCQ by executing the test.bat file shown in Figure 5-1. If users want to program a new design into the EPCQ device, the easiest method is to copy the new .sof file into the demo_batch folder and execute the test.bat. Option “2” will convert the .sof to .jic and option”3” will program .jic file into the EPCQ device. Figure 5-1 Command line of the batch file to program the FPGA and EPCQ device 55..22 AAuuddiioo RReeccoorrddiinngg aanndd PPllaayyiinngg This demonstration shows how to implement an audio recorder and player on DE1-SoC board with the built-in audio CODEC chip. It is developed based on Qsys and Eclipse. Figure 5-2 shows the buttons and slide switches used to interact this demonstration onboard. Users can configure this audio system through two push-buttons and four slide switches:  SW0 is used to specify the recording source to be Line-in or MIC-In.  SW1, SW2, and SW3 are used to specify the recording sample rate such as 96K, 48K, 44.1K, 32K, or 8K.  Table 5-1 and Table 5-2 summarize the usage of slide switches for configuring the audio recorder and player. DE1-SoC User Manual 62 www.terasic.com April 8, 2015 Figure 5-2 Buttons and switches for the audio recorder and player Figure 5-3 shows the block diagram of audio recorder and player design. There are hardware and software parts in the block diagram. The software part stores the Nios II program in the on-chip memory. The software part is built under Eclipse in C programming language. The hardware part is built under Qsys in Quartus II. The hardware part includes all the other blocks such as the “AUDIO Controller”, which is a user-defined Qsys component and it is designed to send audio data to the audio chip or receive audio data from the audio chip. The audio chip is programmed through I2C protocol, which is implemented in C code. The I2C pins from the audio chip are connected to Qsys system interconnect fabric through PIO controllers. The audio chip is configured in master mode in this demonstration. The audio interface is configured as 16-bit I2S mode. 18.432MHz clock generated by the PLL is connected to the MCLK/XTI pin of the audio chip through the audio controller. DE1-SoC User Manual 63 www.terasic.com April 8, 2015 Figure 5-3 Block diagram of the audio recorder and player  Demonstration Setup, File Locations, and Instructions  Hardware project directory: DE1_SoC _Audio  Bitstream used: DE1_SoC_Audio.sof  Software project directory: DE1_SoC _Audio\software  Connect an audio source to the Line-in port  Connect a Microphone to the MIC-in port  Connect a speaker or headset to the Line-out port  Load the bitstream into the FPGA. (note *1)  Load the software execution file into the FPGA. (note *1)  Configure the audio with SW0, as shown in Table 5-1.  Press KEY3 to start/stop audio recording (note *2)  Press KEY2 to start/stop audio playing (note *3) Table 5-1 Slide switches usage for audio source Slide Switches 0 – DOWN Position 1 – UP Position SW0 Audio is from MIC-in Audio is from Line-in DE1-SoC User Manual 64 www.terasic.com April 8, 2015 Table 5-2 Settings of switches for the sample rate of audio recorder and player SW5 (0 – DOWN; 1- UP) SW4 (0 – DOWN; 1-UP) SW3 (0 – DOWN; 1-UP) Sample Rate 0 0 0 96K 0 0 1 48K 0 1 0 44.1K 0 1 1 32K 1 0 0 8K Unlisted combination 96K Note: (1). Execute DE1_SoC _Audio \demo_batch\ DE1-SoC_Audio.bat to download .sof and .elf files. (2). Recording process will stop if the audio buffer is full. (3). Playing process will stop if the audio data is played completely. 55..33 KKaarraaookkee MMaacchhiinnee This demonstration uses the microphone-in, line-in, and line-out ports on DE1-SoC to create a Karaoke machine. The WM8731 CODEC is configured in master mode. The audio CODEC generates AD/DA serial bit clock (BCK) and the left/right channel clock (LRCK) automatically. The I2C interface is used to configure the audio CODEC, as shown in Figure 5-4. The sample rate and gain of the CODEC are set in a similar manner, and the data input from the line-in port is then mixed with the microphone-in port. The result is sent out to the line-out port. The sample rate is set to 48 kHz in this demonstration. The gain of the audio CODEC is reconfigured via I2C bus by pressing the pushbutton KEY0, cycling within ten predefined gain values (volume levels) provided by the device. DE1-SoC User Manual 65 www.terasic.com April 8, 2015 Figure 5-4 Block diagram of the Karaoke machine demonstration  Demonstration Setup, File Locations, and Instructions  Project directory: DE1_SOC_i2sound  Bitstream used: DE1_SOC_i2sound.sof  Connect a microphone to the microphone-in port (pink color)  Connect the audio output of a music player, such as a MP3 player or computer, to the line-in port (blue color)  Connect a headset/speaker to the line-out port (green color)  Load the bitstream into the FPGA by executing the batch file ‘DE1_SOC_i2sound’ in the directory DE1_SOC_i2sound\demo_batch  Users should be able to hear a mixture of microphone sound and the sound from the music player  Press KEY0 to adjust the volume; it cycles between volume level 0 to 9 Figure 5-5 illustrates the setup for this demonstration. DE1-SoC User Manual 66 www.terasic.com April 8, 2015 Figure 5-5 Setup for the Karaoke machine 55..44 SSDDRRAAMM TTeesstt iinn NNiiooss IIII There are many applications use SDRAM as a temporary storage. Both hardware and software designs are provided to illustrate how to perform memory access in Qsys in this demonstration. It also shows how Altera’s SDRAM controller IP accesses SDRAM and how the Nios II processor reads and writes the SDRAM for hardware verification. The SDRAM controller handles complex aspects of accessing SDRAM such as initializing the memory device, managing SDRAM banks, and keeping the devices refreshed at certain interval.  System Block Diagram Figure 5-6 shows the system block diagram of this demonstration. The system requires a 50 MHz clock input from the board. The SDRAM controller is configured as a 64MB controller. The working frequency of the SDRAM controller is 100MHz, and the Nios II program is running on the on-chip memory. DE1-SoC User Manual 67 www.terasic.com April 8, 2015 Figure 5-6 Block diagram of the SDRAM test in Nios II The system flow is controlled by a program running in Nios II. The Nios II program writes test patterns into the entire 64MB of SDRAM first before calling the Nios II system function, alt_dcache_flush_all, to make sure all the data are written to the SDRAM. It then reads data from the SDRAM for data verification. The program will show the progress in nios-terminal when writing/reading data to/from the SDRAM. When the verification process reaches 100%, the result will be displayed in nios-terminal.  Design Tools  Quartus II v13.1  Nios II Eclipse v13.1  Demonstration Source Code  Quartus project directory: DE1_SoC_SDRAM_Nios_Test  Nios II Eclipse directory: DE1_SoC_SDRAM_Nios_Test \Software DE1-SoC User Manual 68 www.terasic.com April 8, 2015  Nios II Project Compilation  Click “Clean” from the “Project” menu of Nios II Eclipse before compiling the reference design in Nios II Eclipse.  Demonstration Batch File The files are located in the directory \DE1_SoC_SDRAM_Nios_Test \demo_batch. The folder includes the following files:  Batch file for USB-Blaster II : DE1_SoC_SDRAM_Nios_Test.bat and DE1_SoC_SDRAM_Nios_Test_bashrc  FPGA configuration file : DE1_SoC_SDRAM_Nios_Test.sof  Nios II program: DE1_SoC_SDRAM_Nios_Test.elf  Demonstration Setup  Quartus II v13.1 and Nios II v13.1 must be pre-installed on the host PC.  Power on the DE1-SoC board.  Connect the DE1-SoC board (J13) to the host PC with a USB cable and install the USB-Blaster driver if necessary.  Execute the demo batch file “DE1_SoC_SDRAM_Nios_Test.bat” from the directory DE1_SoC_SDRAM_Nios_Test\demo_batch  After the program is downloaded and executed successfully, a prompt message will be displayed in nios2-terminal.  Press any button (KEY3~KEY0) to start the SDRAM verification process. Press KEY0 to run the test continuously.  The program will display the test progress and result, as shown in Figure 5-7. DE1-SoC User Manual 69 www.terasic.com April 8, 2015 Figure 5-7 Display of progress and result for the SDRAM test in Nios II 55..55 SSDDRRAAMM TTeesstt iinn VVeerriilloogg DE1-SoC system CD offers another SDRAM test with its test code written in Verilog HDL. The memory size of the SDRAM bank tested is still 64MB.  Function Block Diagram Figure 5-8 shows the function block diagram of this demonstration. The SDRAM controller uses 50 MHz as a reference clock and generates 100 MHz as the memory clock. Figure 5-8 Block diagram of the SDRAM test in Verilog DE1-SoC User Manual 70 www.terasic.com April 8, 2015 RW_test module writes the entire memory with a test sequence first before comparing the data read back with the regenerated test sequence, which is same as the data written to the memory. KEY0 triggers test control signals for the SDRAM, and the LEDs will indicate the test result according to Table 5-3.  Design Tools  Quartus II v13.1  Demonstration Source Code  Project directory: DE1_SoC_SDRAM_RTL_Test  Bitstream used: DE1_SoC_SDRAM_RTL_Test.sof  Demonstration Batch File Demo batch file folder: \DE1_SoC_SDRAM_RTL_Test\demo_batch The directory includes the following files:  Batch file: DE1_SoC_SDRAM_RTL_Test.bat  FPGA configuration file: DE1_SoC_SDRAM_RTL_Test.sof  Demonstration Setup  Quartus II v13.1 must be pre-installed to the host PC.  Connect the DE1-SoC board (J13) to the host PC with a USB cable and install the USB-Blaster II driver if necessary  Power on the DE1_SoC board.  Execute the demo batch file “ DE1_SoC_SDRAM_RTL_Test.bat” from the directoy \DE1_SoC_SDRAM_RTL_Test \demo_batch.  Press KEY0 on the DE1_SoC board to start the verification process. When KEY0 is pressed, the LEDR [2:0] should turn on. When KEY0 is then released, LEDR1 and LEDR2 should start blinking.  After approximately 8 seconds, LEDR1 should stop blinking and stay ON to indicate the test is PASS. Table 5-3 lists the status of LED indicators.  If LEDR2 is not blinking, it means 50MHz clock source is not working.  If LEDR1 failed to remain ON after approximately 8 seconds, the SDRAM test is NG.  Press KEY0 again to repeat the SDRAM test. DE1-SoC User Manual 71 www.terasic.com April 8, 2015 Table 5-3 Status of LED Indicators Name Description LEDR0 Reset LEDR1 ON if the test is PASS after releasing KEY0 LEDR2 Blinks 55..66 TTVV BBooxx DDeemmoonnssttrraattiioonn This demonstration turns DE1-SoC board into a TV box by playing video and audio from a DVD player using the VGA output, audio CODEC and the TV decoder on the DE1-SoC board. Figure 5-9 shows the block diagram of the design. There are two major blocks in the system called I2C_AV_Config and TV_to_VGA. The TV_to_VGA block consists of the ITU-R 656 Decoder, SDRAM Frame Buffer, YUV422 to YUV444, YCbCr to RGB, and VGA Controller. The figure also shows the TV decoder (ADV7180) and the VGA DAC (ADV7123) chip used. The register values of the TV decoder are used to configure the TV decoder via the I2C_AV_Config block, which uses the I2C protocol to communicate with the TV decoder. The TV decoder will be unstable for a time period upon power up, and the Lock Detector block is responsible for detecting this instability. The ITU-R 656 Decoder block extracts YcrCb 4:2:2 (YUV 4:2:2) video signals from the ITU-R 656 data stream sent from the TV decoder. It also generates a data valid control signal, which indicates the valid period of data output. De-interlacing needs to be performed on the data source because the video signal for the TV decoder is interlaced. The SDRAM Frame Buffer and a field selection multiplexer (MUX), which is controlled by the VGA Controller, are used to perform the de-interlacing operation. The VGA Controller also generates data request and odd/even selection signals to the SDRAM Frame Buffer and filed selection multiplexer (MUX). The YUV422 to YUV444 block converts the selected YcrCb 4:2:2 (YUV 4:2:2) video data to the YcrCb 4:4:4 (YUV 4:4:4) video data format. Finally, the YcrCb_to_RGB block converts the YcrCb data into RGB data output. The VGA Controller block generates standard VGA synchronous signals VGA_HS and VGA_VS to enable the display on a VGA monitor. DE1-SoC User Manual 72 www.terasic.com April 8, 2015 Figure 5-9 Block diagram of the TV box demonstration DDeemmoonnssttrraattiioonn SSoouurrccee CCooddee  Project directory: DE1_SoC_TV  Bitstream used: DE1_SoC_TV.sof DDeemmoonnssttrraattiioonn BBaattcchh FFiillee Demo batch directory: \DE1_SoC_TV \demo_batch The folder includes the following files:  Batch file: DE1_SoC_TV.bat  FPGA configuration file : DE1_SoC_TV.sof DDeemmoonnssttrraattiioonn SSeettuupp,, FFiillee LLooccaattiioonnss,, aanndd IInnssttrruuccttiioonnss  Connect a DVD player’s composite video output (yellow plug) to the Video-in RCA jack (J6) on the DE1-SoC board, as shown in Figure 5-10. The DVD player has to be configured to provide:  NTSC output  60Hz refresh rate  4:3 aspect ratio  Non-progressive video DE1-SoC User Manual 73 www.terasic.com April 8, 2015  Connect the VGA output of the DE1-SoC board to a VGA monitor.  Connect the audio output of the DVD player to the line-in port of the DE1-SoC board and connect a speaker to the line-out port. If the audio output jacks from the DVD player are RCA type, an adaptor is needed to convert to the mini-stereo plug supported on the DE1-SoC board.  Load the bitstream into the FPGA by executing the batch file ‘DE1_SoC_TV.bat’ from the directory \DE1_SoC_TV \demo_batch\. Press KEY0 on the DE1-SoC board to reset the demonstration. Figure 5-10 Setup for the TV box demonstration 55..77 PPSS//22 MMoouussee DDeemmoonnssttrraattiioonn A simply PS/2 controller coded in Verilog HDL is provided to demonstrate bi-directional communication with a PS/2 mouse. A comprehensive PS/2 controller can be developed based on it and more sophisticated functions can be implemented such as setting the sampling rate or resolution, which needs to transfer two data bytes at once. More information about the PS/2 protocol can be found on various websites. DE1-SoC User Manual 74 www.terasic.com April 8, 2015  Introduction PS/2 protocol uses two wires for bi-directional communication. One is the clock line and the other one is the data line. The PS/2 controller always has total control over the transmission line, but it is the PS/2 device which generates the clock signal during data transmission.  Data Transmission from Device to the Controller After the PS/2 mouse receives an enabling signal at stream mode, it will start sending out displacement data, which consists of 33 bits. The frame data is cut into three sections and each of them contains a start bit (always zero), eight data bits (with LSB first), one parity check bit (odd check), and one stop bit (always one). The PS/2 controller samples the data line at the falling edge of the PS/2 clock signal. This is implemented by a shift register, which consists of 33 bits. easily be implemented using a shift register of 33 bits, but be cautious with the clock domain crossing problem.  Data Transmission from the Controller to Device When the PS/2 controller wants to transmit data to device, it first pulls the clock line low for more than one clock cycle to inhibit the current transmission process or to indicate the start of a new transmission process, which is usually called as inhibit state. It then pulls low the data line before releasing the clock line. This is called the request state. The rising edge on the clock line formed by the release action can also be used to indicate the sample time point as for a 'start bit. The device will detect this succession and generates a clock sequence in less than 10ms time. The transmit data consists of 12bits, one start bit (as explained before), eight data bits, one parity check bit (odd check), one stop bit (always one), and one acknowledge bit (always zero). After sending out the parity check bit, the controller should release the data line, and the device will detect any state change on the data line in the next clock cycle. If there’s no change on the data line for one clock cycle, the device will pull low the data line again as an acknowledgement which means that the data is correctly received. After the power on cycle of the PS/2 mouse, it enters into stream mode automatically and disable data transmit unless an enabling instruction is received. Figure 5-11 shows the waveform while communication happening on two lines. DE1-SoC User Manual 75 www.terasic.com April 8, 2015 Figure 5-11 Waveform of clock and data signals during data transmission DDeemmoonnssttrraattiioonn SSoouurrccee CCooddee  Project directory: DE1_SoC_PS2_DEMO  Bitstream used: DE1_SoC_PS2_DEMO.sof DDeemmoonnssttrraattiioonn BBaattcchh FFiillee Demo batch file directoy: \DE1_SoC_PS2_DEMO \demo_batch The folder includes the following files:  Batch file: DE1_SoC_PS2_DEMO.bat  FPGA configuration file : DE1_SoC_PS2_DEMO.sof DE1-SoC User Manual 76 www.terasic.com April 8, 2015 DDeemmoonnssttrraattiioonn SSeettuupp,, FFiillee LLooccaattiioonnss,, aanndd IInnssttrruuccttiioonnss  Load the bitstream into the FPGA by executing \DE1_SoC_PS2_DEMO \demo_batch\ DE1_SoC_PS2_DEMO.bat  Plug in the PS/2 mouse  Press KEY[0] to enable data transfer  Press KEY[1] to clear the display data cache  The 7-segment display should change when the PS/2 mouse moves. The LEDR[2:0] will blink according to Table 5-4 when the left-button, right-button, and/or middle-button is pressed. Table 5-4 Description of 7-segment Display and LED Indicators Indicator Name Description LEDR[0] Left button press indicator LEDR[1] Right button press indicator LEDR[2] Middle button press indicator HEX0 Low byte of X displacement HEX1 High byte of X displacement HEX2 Low byte of Y displacement HEX3 High byte of Y displacement 55..88 IIRR EEmmiitttteerr LLEEDD aanndd RReecceeiivveerr DDeemmoonnssttrraattiioonn DE1-SoC system CD has an example of using the IR Emitter LED and IR receiver. This demonstration is coded in Verilog HDL. DE1-SoC User Manual 77 www.terasic.com April 8, 2015 Figure 5-12 Block diagram of the IR emitter LED and receiver demonstration Figure 5-12 shows the block diagram of the design. It implements a IR TX Controller and a IR RX Controller. When KEY0 is pressed, data test pattern generator will generate data to the IR TX Controller continuously. When IR TX Controller is active, it will format the data to be compatible with NEC IR transmission protocol and send it out through the IR emitter LED. The IR receiver will decode the received data and display it on the six HEXs. Users can also use a remote to send data to the IR Receiver. The main function of IR TX /RX controller and IR remote in this demonstration is described in the following sections.  IR TX Controller Users can input 8-bit address and 8-bit command into the IR TX Controller. The IR TX Controller will encode the address and command first before sending it out according to NEC IR transmission protocol through the IR emitter LED. The input clock of IR TX Controller should be 50MHz. The NEC IR transmission protocol uses pulse distance to encode the message bits. Each pulse burst is 562.5µs in length with a carrier frequency of 38kHz (26.3µs). Figure 5-13 shows the duration of logical “1” and “0”. Logical bits are transmitted as follows: • Logical '0' – a 562.5µs pulse burst followed by a 562.5µs space with a total transmit time of 1.125ms DE1-SoC User Manual 78 www.terasic.com April 8, 2015 • Logical '1' – a 562.5µs pulse burst followed by a 1.6875ms space with a total transmit time of 2.25ms Figure 5-13 Duration of logical “1”and logical “0” Figure 5-14 shows a frame of the protocol. Protocol sends a lead code first, which is a 9ms leading pulse burst, followed by a 4.5ms window. The second inversed data is sent to verify the accuracy of the information received. A final 562.5µs pulse burst is sent to signify the end of message transmission. Because the data is sent in pair (original and inverted) according to the protocol, the overall transmission time is constant. Figure 5-14 Typical frame of NEC protocol Note: The signal received by IR Receiver is inverted. For instance, if IR TX Controller sends a lead code 9 ms high and then 4.5 ms low, IR Receiver will receive a 9 ms low and then 4.5 ms high lead code. DE1-SoC User Manual 79 www.terasic.com April 8, 2015  IR Remote When a key on the remote controller show in Figure 5-15 is pressed, the remote controller will emit a standard frame, as shown in Table 5-5. The beginning of the frame is the lead code, which represents the start bit, followed by the key-related information. The last bit end code represents the end of the frame. The value of this frame is completely inverted at the receiving end. Figure 5-15 The remote controller used in this demonstration Table 5-5 Key Code Information for Each Key on the Remote Key Key Code Key Key Code Key Key Code Key Key Code 0x0F 0x13 0x10 0x12 0x01 0x02 0x03 0x1A 0x04 0x05 0x06 0x1E 0x07 0x08 0x09 0x1B 0x11 0x00 0x17 0x1F 0x16 0x14 0x18 0x0C DE1-SoC User Manual 80 www.terasic.com April 8, 2015 Lead Code 1bit Custom Code 16bits Key Code 8bits Inv Key Code 8bits End Code 1bit Figure 5-16 The transmitting frame of the IR remote controller  IR RX Controller The following demonstration shows how to implement the IP of IR receiver controller in the FPGA. Figure 5-17 shows the modules used in this demo, including Code Detector, State Machine, and Shift Register. At the beginning the IR receiver demodulates the signal inputs to the Code Detector . The Code Detector will check the Lead Code and feedback the examination result to the State Machine. The State Machine block will change the state from IDLE to GUIDANCE once the Lead Code is detected. If the Code Detector detects the Custom Code status, the current state will change from GUIDANCE to DATAREAD state. The Code Detector will also save the receiving data and output to the Shift Register and display on the 7-segment. Figure 5-18 shows the state shift diagram of State Machine block. The input clock should be 50MHz. Figure 5-17 Modules in the IR Receiver controller DE1-SoC User Manual 81 www.terasic.com April 8, 2015 Figure 5-18 State shift diagram of State Machine block DDeemmoonnssttrraattiioonn SSoouurrccee CCooddee  Project directory: DE1_SoC_IR  Bitstream used: DE1_SOC_IR.sof DDeemmoonnssttrraattiioonn BBaattcchh FFiillee Demo batch file directory: DE1_SoC_IR \demo_batch The folder includes the following files:  Batch file: DE1_SoC_IR.bat  FPGA configuration file : DE1_SOC_IR.sof DDeemmoonnssttrraattiioonn SSeettuupp,, FFiillee LLooccaattiioonnss,, aanndd IInnssttrruuccttiioonnss  Load the bitstream into the FPGA by executing DE1_SoC_IR \demo_batch\ DE1_SoC_IR.bat  Keep pressing KEY[0] to enable the pattern to be sent out continuously by the IR TX Controller.  Observe the six HEXs according to Table 5-6  Release KEY[0] to stop the IR TX.  Point the IR receiver with the remote and press any button DE1-SoC User Manual 82 www.terasic.com April 8, 2015  Observe the six HEXs according to Table 5-6 Table 5-6 Detailed Information of the Indicators Indicator Name Description HEX5 Inversed high byte of DATA(Key Code) HEX4 Inversed low byte of DATA(Key Code) HEX3 High byte of ADDRESS(Custom Code) HEX2 Low byte of ADDRESS(Custom Code) HEX1 High byte of DATA(Key Code) HEX0 Low byte of DATA (Key Code) 55..99 AADDCC RReeaaddiinngg This demonstration illustrates steps to evaluate the performance of the 8-channel 12-bit A/D Converter ADC7928. The DC 5.0V on the 2x5 header is used to drive the analog signals by a trimmer potentiometer. The voltage can be adjusted within the range between 0 and 5.0V. The 12-bit voltage measurement is displayed on the NIOS II console. Figure 5-19 shows the block diagram of this demonstration. If the input voltage is -2.5V ~ 2.5V, a pre-scale circuit can be used to adjust it to 0 ~ 5V. DE1-SoC User Manual 83 www.terasic.com April 8, 2015 Figure 5-19 Block diagram of ADC reading Figure 5-20 depicts the pin arrangement of the 2x5 header. This header is the input source of ADC convertor in this demonstration. Users can connect a trimmer to the specified ADC channel (ADC_IN0 ~ ADC_IN7) that provides voltage to the ADC convert. The FPGA will read the associated register in the convertor via serial interface and translates it to voltage value to be displayed on the Nios II console. Figure 5-20 Pin distribution of the 2x5 Header for the ADC  System Requirements The following items are required for this demonstration. DE1-SoC User Manual 84 www.terasic.com April 8, 2015  DE1-SoC board x1  Trimmer Potentiometer x1  Wire Strip x3  Demonstration File Locations  Hardware project directory: DE1_SoC_ADC  Bitstream used: DE1_SoC_ADC.sof  Software project directory: DE1_SoC_ADC software  Demo batch file : DE1_SoC_ADC\demo_batch\ DE1_SoC_ADC.bat  Demonstration Setup and Instructions  Connect the trimmer to corresponding ADC channel on the 2x5 header, as shown in Figure 5-21, as well as the +5V and GND signals. The setup shown above is connected to ADC channel 0.  Execute the demo batch file DE1_SoC_ADC.bat to load the bitstream and software execution file to the FPGA.  The Nios II console will display the voltage of the specified channel voltage result information Figure 5-21 Hardware setup for the ADC reading demonstration DE1-SoC User Manual 85 www.terasic.com April 8, 2015 Chapter 6 Examples for HPS SoC This chapter provides several C-code examples based on the Altera SoC Linux built by Yocto project. These examples demonstrates major features connected to HPS interface on DE1-SoC board such as users LED/KEY, I2C interfaced G-sensor, and I2C MUX. All the associated files can be found in the directory Demonstrations/SOC of the DE1_SoC System CD. Please refer to Chapter 5 "Running Linux on the DE1-SoC board" from the DE1-SoC_Getting_Started_Guide.pdf to run Linux on DE1-SoC board.  Installation of the Demonstrations To install the demonstrations on the host computer: Copy the directory Demonstrations into a local directory of your choice. Altera SoC EDS v13.1 is required for users to compile the c-code project. 66..11 HHeelllloo PPrrooggrraamm This demonstration shows how to develop first HPS program with Altera SoC EDS tool. Please refer to My_First_HPS.pdf from the system CD for more details. The major procedures to develop and build HPS project are:  Install Altera SoC EDS on the host PC.  Create program .c/.h files with a generic text editor  Create a "Makefile" with a generic text editor  Build the project under Altera SoC EDS DE1-SoC User Manual 86 www.terasic.com April 8, 2015  Program File The main program for the Hello World demonstration is:  Makefile A Makefile is required to compile a project. The Makefile used for this demo is:  Compile Please launch Altera SoC EDS Command Shell to compile a project by executing C:\altera\13.1\embedded\Embedded_Command_Shell.bat The "cd" command can change the current directory to where the Hello World project is located. DE1-SoC User Manual 87 www.terasic.com April 8, 2015 The "make" command will build the project. The executable file "my_first_hps" will be generated after the compiling process is successful. The "clean all" command removes all temporary files.  Demonstration Source Code  Build tool: Altera SoC EDS v13.1  Project directory: \Demonstration\SoC\my_first_hps  Binary file: my_first_hps  Build command: make ("make clean" to remove all temporary files)  Execute command: ./my_first_hps  Demonstration Setup  Connect a USB cable to the USB-to-UART connector (J4) on the DE1-SoC board and the host PC.  Copy the demo file "my_first_hps" into a microSD card under the "/home/root" folder in Linux.  Insert the booting microSD card into the DE1-SoC board.  Power on the DE1-SoC board.  Launch PuTTY and establish connection to the UART port of Putty. Type "root" to login Altera Yocto Linux.  Type "./my_first_hps" in the UART terminal of PuTTY to start the program, and the "Hello World!" message will be displayed in the terminal. 66..22 UUsseerrss LLEEDD aanndd KKEEYY This demonstration shows how to control the users LED and KEY by accessing the register of GPIO controller through the memory-mapped device driver. The memory-mapped device driver allows developer to access the system physical memory.  Function Block Diagram Figure 6-1 shows the function block diagram of this demonstration. The users LED and KEY are connected to the GPIO1 controller in HPS. The behavior of GPIO controller is controlled by the register in GPIO controller. The registers can be accessed by application software through the memory-mapped device driver, which is built into Altera SoC Linux. DE1-SoC User Manual 88 www.terasic.com April 8, 2015 Figure 6-1 Block diagram of GPIO demonstration  Block Diagram of GPIO Interface The HPS provides three general-purpose I/O (GPIO) interface modules. Figure 6-2 shows the block diagram of GPIO Interface. GPIO[28..0] is controlled by the GPIO0 controller and GPIO[57..29] is controlled by the GPIO1 controller. GPIO[70..58] and input-only GPI[13..0] are controlled by the GPIO2 controller. Figure 6-2 Block diagram of GPIO Interface DE1-SoC User Manual 89 www.terasic.com April 8, 2015  GPIO Register Block The behavior of I/O pin is controlled by the registers in the register block. There are three 32-bit registers in the GPIO controller used in this demonstration. The registers are:  gpio_swporta_dr: write output data to output I/O pin  gpio_swporta_ddr: configure the direction of I/O pin  gpio_ext_porta: read input data of I/O input pin The gpio_swporta_ddr configures the LED pin as output pin and drives it high or low by writing data to the gpio_swporta_dr register. The first bit (least significant bit) of gpio_swporta_dr controls the direction of first IO pin in the associated GPIO controller and the second bit controls the direction of second IO pin in the associated GPIO controller and so on. The value "1" in the register bit indicates the I/O direction is output, and the value "0" in the register bit indicates the I/O direction is input. The first bit of gpio_swporta_dr register controls the output value of first I/O pin in the associated GPIO controller, and the second bit controls the output value of second I/O pin in the associated GPIO controller and so on. The value "1" in the register bit indicates the output value is high, and the value "0" indicates the output value is low. The status of KEY can be queried by reading the value of gpio_ext_porta register. The first bit represents the input status of first IO pin in the associated GPIO controller, and the second bit represents the input status of second IO pin in the associated GPIO controller and so on. The value "1" in the register bit indicates the input state is high, and the value "0" indicates the input state is low.  GPIO Register Address Mapping The registers of HPS peripherals are mapped to HPS base address space 0xFC000000 with 64KB size. The registers of the GPIO1 controller are mapped to the base address 0xFF708000 with 4KB size, and the registers of the GPIO2 controller are mapped to the base address 0xFF70A000 with 4KB size, as shown in Figure 6-3. DE1-SoC User Manual 90 www.terasic.com April 8, 2015 Figure 6-3 GPIO address map  Software API Developers can use the following software API to access the register of GPIO controller.  open: open memory mapped device driver  mmap: map physical memory to user space  alt_read_word: read a value from a specified register  alt_write_word: write a value into a specified register  munmap: clean up memory mapping  close: close device driver. Developers can also use the following MACRO to access the register  alt_setbits_word: set specified bit value to one for a specified register  alt_clrbits_word: set specified bit value to zero for a specified register The program must include the following header files to use the above API to access the registers of GPIO controller. #include #include #include DE1-SoC User Manual 91 www.terasic.com April 8, 2015 #include #include "hwlib.h" #include "socal/socal.h" #include "socal/hps.h" #include "socal/alt_gpio.h"  LED and KEY Control Figure 6-4 shows the HPS users LED and KEY pin assignment for the DE1_SoC board. The LED is connected to HPS_GPIO53 and the KEY is connected to HPS_GPIO54. They are controlled by the GPIO1 controller, which also controls HPS_GPIO29 ~ HPS_GPIO57. Figure 6-4 Pin assignment of LED and KEY Figure 6-5 shows the gpio_swporta_ddr register of the GPIO1 controller. The bit-0 controls the pin direction of HPS_GPIO29. The bit-24 controls the pin direction of HPS_GPIO53, which connects to HPS_LED, the bit-25 controls the pin direction of HPS_GPIO54, which connects to HPS_KEY and so on. The pin direction of HPS_LED and HPS_KEY are controlled by the bit-24 and bit-25 in the gpio_swporta_ddr register of the GPIO1 controller, respectively. Similarly, the output status of HPS_LED is controlled by the bit-24 in the gpio_swporta_dr register of the GPIO1 controller. The status of KEY can be queried by reading the value of the bit-24 in the gpio_ext_porta register of the GPIO1 controller. DE1-SoC User Manual 92 www.terasic.com April 8, 2015 Figure 6-5 gpio_swporta_ddr register in the GPIO1 controller The following mask is defined in the demo code to control LED and KEY direction and LED’s output value. #define USER_IO_DIR (0x01000000) #define BIT_LED (0x01000000) #define BUTTON_MASK (0x02000000) The following statement is used to configure the LED associated pins as output pins. alt_setbits_word( ( virtual_base + ( ( uint32_t )( ALT_GPIO1_SWPORTA_DDR_ADDR ) & ( uint32_t )( HW_REGS_MASK ) ) ), USER_IO_DIR ); The following statement is used to turn on the LED. alt_setbits_word( ( virtual_base + ( ( uint32_t )( ALT_GPIO1_SWPORTA_DR_ADDR ) & ( uint32_t )( HW_REGS_MASK ) ) ), BIT_LED ); The following statement is used to read the content of gpio_ext_porta register. The bit mask is used to check the status of the key. alt_read_word( ( virtual_base + ( ( uint32_t )( ALT_GPIO1_EXT_PORTA_ADDR ) & ( uint32_t )( HW_REGS_MASK ) ) ) ); DE1-SoC User Manual 93 www.terasic.com April 8, 2015  Demonstration Source Code  Build tool: Altera SoC EDS V13.1  Project directory: \Demonstration\SoC\hps_gpio  Binary file: hps_gpio  Build command: make ('make clean' to remove all temporal files)  Execute command: ./hps_gpio  Demonstration Setup  Connect a USB cable to the USB-to-UART connector (J4) on the DE1-SoC board and the host PC.  Copy the executable file "hps_gpio" into the microSD card under the "/home/root" folder in Linux.  Insert the booting micro SD card into the DE1-SoC board.  Power on the DE1-SoC board.  Launch PuTTY and establish connection to the UART port of Putty. Type "root" to login Altera Yocto Linux.  Type "./hps_gpio " in the UART terminal of PuTTY to start the program.  HPS_LED will flash twice and users can control the user LED with push-button.  Press HPS_KEY to light up HPS_LED.  Press "CTRL + C" to terminate the application. 66..33 II22CC IInntteerrffaacceedd GG--sseennssoorr This demonstration shows how to control the G-sensor by accessing its registers through the built-in I2C kernel driver in Altera Soc Yocto Powered Embedded Linux.  Function Block Diagram Figure 6-6 shows the function block diagram of this demonstration. The G-sensor on the DE1_SoC board is connected to the I2C0 controller in HPS. The G-Sensor I2C 7-bit device address is 0x53. The system I2C bus driver is used to access the register files in the G-sensor. The G-sensor interrupt DE1-SoC User Manual 94 www.terasic.com April 8, 2015 signal is connected to the PIO controller. This demonstration uses polling method to read the register data. Figure 6-6 Block diagram of the G-sensor demonstration  I2C Driver The procedures to read a register value from G-sensor register files by the existing I2C bus driver in the system are: 1. Open I2C bus driver "/dev/i2c-0": file = open("/dev/i2c-0", O_RDWR); 2. Specify G-sensor's I2C address 0x53: ioctl(file, I2C_SLAVE, 0x53); 3. Specify desired register index in g-sensor: write(file, &Addr8, sizeof(unsigned char)); 4. Read one-byte register value: read(file, &Data8, sizeof(unsigned char)); The G-sensor I2C bus is connected to the I2C0 controller, as shown in the Figure 6-7. The driver name given is '/dev/i2c-0'. Figure 6-7 Connection of HPS I2C signals The step 4 above can be changed to the following to write a value into a register. write(file, &Data8, sizeof(unsigned char)); The step 4 above can also be changed to the following to read multiple byte values. DE1-SoC User Manual 95 www.terasic.com April 8, 2015 read(file, &szData8, sizeof(szData8)); // where szData is an array of bytes The step 4 above can be changed to the following to write multiple byte values. write(file, &szData8, sizeof(szData8)); // where szData is an array of bytes  G-sensor Control The ADI ADXL345 provides I2C and SPI interfaces. I2C interface is selected by setting the CS pin to high on the DE1_SoC board. The ADI ADXL345 G-sensor provides user-selectable resolution up to 13-bit ± 16g. The resolution can be configured through the DATA_FORAMT(0x31) register. The data format in this demonstration is configured as:  Full resolution mode  ± 16g range mode  Left-justified mode The X/Y/Z data value can be derived from the DATAX0(0x32), DATAX1(0x33), DATAY0(0x34), DATAY1(0x35), DATAZ0(0x36), and DATAX1(0x37) registers. The DATAX0 represents the least significant byte and the DATAX1 represents the most significant byte. It is recommended to perform multiple-byte read of all registers to prevent change in data between sequential registers read. The following statement reads 6 bytes of X, Y, or Z value. read(file, szData8, sizeof(szData8)); // where szData is an array of six-bytes  Demonstration Source Code  Build tool: Altera SoC EDS v13.1  Project directory: \Demonstration\SoC\hps_gsensor  Binary file: gsensor  Build command: make ('make clean' to remove all temporal files)  Execute command: ./gsensor [loop count]  Demonstration Setup  Connect a USB cable to the USB-to-UART connector (J4) on the DE1-SoC board and the host PC. DE1-SoC User Manual 96 www.terasic.com April 8, 2015  Copy the executable file "gsensor" into the microSD card under the "/home/root" folder in Linux.  Insert the booting microSD card into the DE1-SoC board.  Power on the DE1-SoC board.  Launch PuTTY to establish connection to the UART port of DE1-SoC board. Type "root" to login Yocto Linux.  Execute "./gsensor" in the UART terminal of PuTTY to start the G-sensor polling.  The demo program will show the X, Y, and Z values in the PuTTY, as shown in Figure 6-8. Figure 6-8 Terminal output of the G-sensor demonstration  Press "CTRL + C" to terminate the program. 66..44 II22CC MMUUXX TTeesstt The I2C bus on DE1-SoC is originally accessed by FPGA only. This demonstration shows how to switch the I2C multiplexer for HPS to access the I2C bus.  Function Block Diagram Figure 6-9 shows the function block diagram of this demonstration. The I2C bus from both FPGA and HPS are connected to an I2C multiplexer. It is controlled by HPS_I2C_CONTROL, which is connected to the GPIO1 controller in HPS. The HPS I2C is connected to the I2C0 controller in HPS, as well as the G-sensor. DE1-SoC User Manual 97 www.terasic.com April 8, 2015 Figure 6-9 Block diagram of the I2C MUX test demonstration  HPS_I2C_CONTROL Control HPS_I2C_CONTROL is connected to HPS_GPIO48, which is bit-19 of the GPIO1 controller. Once HPS gets access to the I2C bus, it can then access Audio CODEC and TV Decoder when the HPS_I2C_CONTROL signal is set to high. The following mask in the demo code is defined to control the direction and output value of HPS_I2C_CONTROL. #define HPS_I2C_CONTROL ( 0x00080000 ) The following statement is used to configure the HPS_I2C_CONTROL associated pins as output pin. alt_setbits_word( ( virtual_base + ( ( uint32_t )( ALT_GPIO1_SWPORTA_DDR_ADDR ) & ( uint32_t )( HW_REGS_MASK ) ) ), HPS_I2C_CONTROL ); The following statement is used to set HPS_I2C_CONTROL high. alt_setbits_word( ( virtual_base + ( ( uint32_t )( ALT_GPIO1_SWPORTA_DR_ADDR ) & ( uint32_t )( HW_REGS_MASK ) ) ), HPS_I2C_CONTROL ); The following statement is used to set HPS_I2C_CONTROL low. alt_clrbits_word( ( virtual_base + ( ( uint32_t )( ALT_GPIO1_SWPORTA_DR_ADDR ) & ( uint32_t )( HW_REGS_MASK ) ) ), HPS_I2C_CONTROL ); DE1-SoC User Manual 98 www.terasic.com April 8, 2015  I2C Driver The procedures to read register value from TV Decoder by the existing I2C bus driver in the system are:  Set HPS_I2C_CONTROL high for HPS to access I2C bus.  Open the I2C bus driver "/dev/i2c-0": file = open("/dev/i2c-0", O_RDWR);  Specify the I2C address 0x20 of ADV7180: ioctl(file, I2C_SLAVE, 0x20);  Read or write registers;  Set HPS_I2C_CONTROL low to release the I2C bus.  Demonstration Source Code  Build tool: Altera SoC EDS v13.1  Project directory: \Demonstration\SoC\ hps_i2c_switch  Binary file: i2c_switch  Build command: make ('make clean' to remove all temporal files)  Execute command: ./ i2c_switch  Demonstration Setup  Connect a USB cable to the USB-to-UART connector (J4) on the DE1-SoC board and host PC.  Copy the executable file " i2c_switch " into the microSD card under the "/home/root" folder in Linux.  Insert the booting microSD card into the DE1-SoC board.  Power on the DE1-SoC board.  Launch PuTTY to establish connection to the UART port of DE1_SoC borad. Type "root" to login Yocto Linux.  Execute "./ i2c_switch " in the UART terminal of PuTTY to start the I2C MUX test.  The demo program will show the result in the Putty, as shown in Figure 6-10. Figure 6-10 Terminal output of the I2C MUX Test Demonstration  Press "CTRL + C" to terminate the program. DE1-SoC User Manual 99 www.terasic.com April 8, 2015 Chapter 7 Examples for using both HPS SoC and FGPA Although HPS and FPGA can operate independently, they are tightly coupled via a high-bandwidth system interconnect built from high-performance ARM AMBA® AXITM bus bridges. Both FPGA fabric and HPS can access to each other via these interconnect bridges. This chapter provides demonstrations on how to achieve superior performance and lower latency through these interconnect bridges when comparing to solutions containing a separate FPGA and discrete processor. 77..11 HHPPSS CCoonnttrrooll LLEEDD aanndd HHEEXX This demonstration shows how HPS controls the FPGA LED and HEX through Lightweight HPS-to-FPGA Bridge. The FPGA is configured by HPS through FPGA manager in HPS.  A brief view on FPGA manager The FPGA manager in HPS configures the FPGA fabric from HPS. It also monitors the state of FPGA and drives or samples signals to or from the FPGA fabric. The application software is provided to configure FPGA through the FPGA manager. The FPGA configuration data is stored in the file with .rbf extension. The MSEL[4:0] must be set to 01010 or 01110 before executing the application software on HPS.  Function Block Diagram Figure 7-1 shows the block diagram of this demonstration. The HPS uses Lightweight HPS-to-FPGA AXI Bridge to communicate with FPGA. The hardware in FPGA part is built into DE1-SoC User Manual 100 www.terasic.com April 8, 2015 Qsys. The data transferred through Lightweight HPS-to-FPGA Bridge is converted into Avalon-MM master interface. Both PIO Controller and HEX Controller work as Avalon-MM slave in the system. They control the associated pins to change the state of LED and HEX. This is similar to a system using Nios II processor to control LED and HEX. Figure 7-1 FPGA LED and HEX are controlled by HPS  LED and HEX control The Lightweight HPS-to-FPGA Bridge is a peripheral of HPS. The software running on Linux cannot access the physical address of the HPS peripheral. The physical address must be mapped to the user space before the peripheral can be accessed. Alternatively, a customized device driver module can be added to the kernel. The entire CSR span of HPS is mapped to access various registers within that span. The mapping function and the macro defined below can be reused if any other peripherals whose physical address is also in this span. The start address of Lightweight HPS-to-FPGA Bridge after mapping can be retrieved by ALT_LWFPGASLVS_OFST, which is defined in altera_hps hardware library. The slave IP connected to the bridge can then be accessed through the base address and the register offset in these IPs. For instance, the base address of the PIO slave IP in this system is 0x0001_0040, the direction control register offset is 0x01, and the data register offset is 0x00. The following statement is used to retrieve the base address of PIO slave IP. h2p_lw_led_addr=virtual_base+( ( unsigned long )( ALT_LWFPGASLVS_OFST + LED_PIO_BASE ) & ( unsigned long)( HW_REGS_MASK ) ); DE1-SoC User Manual 101 www.terasic.com April 8, 2015 Considering this demonstration only needs to set the direction of PIO as output, which is the default direction of the PIO IP, the step above can be skipped. The following statement is used to set the output state of the PIO. alt_write_word(h2p_lw_led_addr, Mask ); The Mask in the statement decides which bit in the data register of the PIO IP is high or low. The bits in data register decide the output state of the pins connected to the LEDs. The HEX controlling part is similar to the LED. Since Linux supports multi-thread software, the software for this system creates two threads. One controls the LED and the other one controls the HEX. The system calls pthread_create, which is called in the main function to create a sub-thread, to complete the job. The program running in the sub-thread controls the LED flashing in a loop. The main-thread in the main function controls the digital shown on the HEX that keeps changing in a loop. The state of LED and HEX state change simultaneously when the FPGA is configured and the software is running on HPS.  Demonstration Source Code  Build tool: Altera SoC EDS V13.1  Project directory: \Demonstration\ SoC_FPGA\HPS_LED_HEX  Quick file directory:\ Demonstration\ SoC_FPGA\HPS_LED_HEX\ quickfile  FPGA configuration file : soc_system_dc.rbf  Binary file: HPS_LED_HEX and hps_config_fpga  Build app command: make ('make clean' to remove all temporal files)  Execute app command:./hps_config_fpga soc_system_dc.rbf and./HPS_LED_HEX  DDeemmoonnssttrraattiioonn SSeettuupp  Quartus II and Nios II must be installed on the host PC.  The MSEL[4:0] is set to 01010 or 01110.  Connect a USB cable to the USB-Blaster II connector (J13) on the DE1-SoC board and the host PC. Install the USB-Blaster II driver if necessary.  Connect a USB cable to the USB-to-UART connector (J4) on the DE1-SoC board and the host PC.  Copy the executable files "hps_config_fpga" and "HPS_LED_HEX", and the FPGA configuration file "soc_system_dc.rbf" into the microSD card under the "/home/root" folder in Linux.  Insert the booting microSD card into the DE1-SoC board. Please refer to the chapter 5 DE1-SoC User Manual 102 www.terasic.com April 8, 2015 "Running Linux on the DE1-SoC board" on DE1-SoC_Getting_Started_Guide.pdf on how to build a booting microSD card image.  Power on the DE1-SoC board.  Launch PuTTY to establish connection to the UART port of the DE1-SoC board. Type "root" to login Altera Yocto Linux.  Execute "./hps_config_fpga soc_system_dc.rbf " in the UART terminal of PuTTY to configure the FPGA through the FPGA manager. After the configuration is successful, the message shown in Figure 7-2Figure72 will be displayed in the terminal. Figure 7-2 Running the application to configure the FPGA  Execute "./HPS_LED_HEX " in the UART terminal of PuTTY to start the program.  The message shown in Figure 7-3OLE_LINK4, will be displayed in the terminal. The LED[9:0] will be flashing and the number on the HEX[5:0] will keep changing simultaneously. Figure 7-3 Running result in the terminal of PuTTY  Press "CTRL + C" to terminate the program. DE1-SoC User Manual 103 www.terasic.com April 8, 2015 77..22 DDEE11--SSooCC CCoonnttrrooll PPaanneell The DE1-SoC Control Panel is a more comprehensive example. It demonstrates:  Control HPS LED and FPGA LED/HEX  Query the status of buttons connected to HPS and FPGA  Configure and query G-sensor connected to HPS  Control Video-in and VGA-out connected to FPGA  Control IR receiver connected to FPGA This example not only controls the peripherals of HPS and FPGA, but also shows how to implement a GUI program on Linux. Figure 7-4OLE_LINK4 is the screenshot of DE1-SOC Control Panel. Figure 7-4 Screenshot of DE1-SoC Control Panel Please refer to DE1-SoC_Control_Panel.pdf, which is included in the DE1-SOC System CD for more information on how to build a GUI program step by step. 77..33 DDEE11--SSooCC LLiinnuuxx FFrraammee BBuuffffeerr PPrroojjeecctt The DE1-SoC Linux Frame Buffer Project is a example that a VGA monitor is utilized as a standard output interface for the linux operate system. The Quartus II project is located at this path: Demonstrations/SOC_FPGA/DE1_SOC_Linux_FB. The soc_system.rbf file in the project is used for configuring FPGA through HPS. The .rbf file is converted form DE1_SOC_Linux_FB.sof by clicking the sof_to_rbf.bat. The project is adopted for the following demonstrations. DE1-SoC User Manual 104 www.terasic.com April 8, 2015  DE1_SoC Linux Console with framebuffer  DE1_SoC LXDE with Desktop  DE1_SoC Ubuntu Desktop The SD image file for the demonstrations above can be downloaded in the design resources for DE1-SoC at Terasic website. These examples provide a GUI environment for further developing for the users. For example, a QT application can run on the system. Figure 7-5 Screenshot of DE1-SoC Linux Console with framebuffer Please refer to DE1-SoC_Getting_Started_Guide about how to get the SD images and create a boot SD card. DE1-SoC User Manual 105 www.terasic.com April 8, 2015 Chapter 8 Programming the EPCQ Device This chapter describes how to program the quad serial configuration (EPCQ) device with Serial Flash Loader (SFL) function via the JTAG interface. Users can program EPCQ devices with a JTAG indirect configuration (.jic) file, which is converted from a user-specified SRAM object file (.sof) in Quartus. The .sof file is generated after the project compilation is successful. The steps of converting .sof to .jic in Quartus II are listed below. 88..11 BBeeffoorree PPrrooggrraammmmiinngg BBeeggiinnss The FPGA should be set to AS x4 mode i.e. MSEL[4..0] = “10010” to use the quad Flash as a FPGA configuration device. 88..22 CCoonnvveerrtt ..SSOOFF FFiillee ttoo ..JJIICC FFiillee 1. Choose Convert Programming Files from the File menu of Quartus II, as shown in Figure 8-1. DE1-SoC User Manual 106 www.terasic.com April 8, 2015 Figure 8-1 File menu of Quartus II 2. Select JTAG Indirect Configuration File (.jic) from the Programming file type field in the dialog of Convert Programming Files. 3. Choose EPCQ256 from the Configuration device field. 4. Choose Active Serial x4 from the Model filed. 5. Browse to the target directory from the File name field and specify the name of output file. 6. Click on the SOF data in the section of Input files to convert, as shown in Figure 8-2. DE1-SoC User Manual 107 www.terasic.com April 8, 2015 Figure 8-2 Dialog of “Convert Programming Files” 7. Click Add File. 8. Select the .sof to be converted to a .jic file from the Open File dialog. 9. Click Open. 10. Click on the Flash Loader and click Add Device, as shown in Figure 8-3. 11. Click OK and the Select Devices page will appear. DE1-SoC User Manual 108 www.terasic.com April 8, 2015 Figure 8-3 Click on the “Flash Loader” 12. Select the targeted FPGA to be programed into the EPCQ, as shown in Figure 8-4. 13. Click OK and the Convert Programming Files page will appear, as shown in Figure 8-5. 14. Click Generate. DE1-SoC User Manual 109 www.terasic.com April 8, 2015 Figure 8-4 “Select Devices” page Figure 8-5 “Convert Programming Files” page after selecting the device DE1-SoC User Manual 110 www.terasic.com April 8, 2015 88..33 WWrriittee JJIICC FFiillee iinnttoo tthhee EEPPCCQQ DDeevviiccee When the conversion of SOF-to-JIC file is complete, please follow the steps below to program the EPCQ device with the .jic file created in Quartus II Programmer. 1. Set MSEL[4..0] = “10010” 2. Choose Programmer from the Tools menu and the Chain.cdf window will appear. 3. Click Auto Detect and then select the correct device. Both FPGA device and HPS should be detected, as shown in Figure 8-6. 4. Double click the green rectangle region shown in Figure 8-6 and the Select New Programming File page will appear. Select the .jic file to be programmed. 5. Program the EPCQ device by clicking the corresponding Program/Configure box. A factory default SFL image will be loaded, as shown in Figure 8-7. 6. Click Start to program the EPCQ device. Figure 8-6 Two devices are detected in the Quartus II Programmer DE1-SoC User Manual 111 www.terasic.com April 8, 2015 Figure 8-7 Quartus II programmer window with one .jic file 88..44 EErraassee tthhee EEPPCCQQ DDeevviiccee The steps to erase the existing file in the EPCQ device are: 1. Set MSEL[4..0] = “10010” 2. Choose Programmer from the Tools menu and the Chain.cdf window will appear. 3. Click Auto Detect, and then select correct device, both FPGA device and HPS will detected. (See Figure 8-6) 4. Double click the green rectangle region shown in Figure 8-6, and the Select New Programming File page will appear. Select the correct .jic file. 5. Erase the EPCQ device by clicking the corresponding Erase box. A factory default SFL image will be loaded, as shown in Figure 8-8. DE1-SoC User Manual 112 www.terasic.com April 8, 2015 Figure 8-8 Erase the EPCQ device in Quartus II Programmer 6. Click Start to erase the EPCQ device. 88..55 NNiiooss IIII BBoooott ffrroomm EEPPCCQQ DDeevviiccee iinn QQuuaarrttuuss IIII vv1133..11 There is a known problem in Quartus II software that the Quartus Programmer must be used to program the EPCQ device on DE1-SoC board. Please refer to Altera’s website here with details step by step. DE1-SoC User Manual 113 www.terasic.com April 8, 2015 Chapter 9 Appendix 99..11 RReevviissiioonn HHiissttoorryy Version Change Log V0.1 Initial Version (Preliminary) V0.2 Add Chapter 5 and Chapter 6 V0.3 Modify Chapter 3 V0.4 Add Chapter 3 HPS V0.5 Modify Chapter 3 V1.0 Modify Chapter 8 V1.1 Modify section 3.3 V1.2 1. Add Sectiom 7.3 2. Modify Figure 3-2 V1.2.1 Modify Figure 3-2 V1.2.2d Modify Figure 5-5 descriptions of remote controller Copyright © 2015 Terasic Technologies. All rights reserved.