77
T.K. Ghosh and M.A. Prelas, Energy Resources and Systems:
© Springer Science + Business Media B.V. 2009
3 UNITS AND UNIT CONVERSIONS
Abstract
The type of units used to describe the energy content of a resource depends on the
resource itself. As a consequence, a variety of units are used in the energy industry.
The conversion of one unit to another unit is essential for comparison purpose and
also to prevent various mishaps. Scientists and engineers working in the energy
related industry should know how to convert gallons to liters, and vice versa. The
difference between energy content and power output should be clear to all professionals
in the energy field. This chapter addresses various units used in the energy
industry and their conversion from one unit to another unit.
3.1 Introduction
One of the most important endeavors of an engineer is to understand the units used
in describing, evaluating, and comparing various systems. Two systems of units
exist in science and engineering. These two systems are Système International
d’unités (in short SI system) and British system. The SI system is also known as
countries yet to adopt the metric system officially. In 1866, the use of the metric
system was made legal but not mandatory in the United States by the Metric Act
of 1866 (P.L. 39-183) [1]. Since then various other laws were passed in the U.S.
Congress to promote the use of metric systems [2, 3].
From a historical perspective, energy has been measured by British units. The
energy system may be the only system that was affected significantly when
implementation of the metric system occurred. For example, Joules, the common
measurement used in the metric system is seldom used in measuring energy
resources in our day to day life. As can be seen from Table 3.1, the most common
units used to measure various energy resources are still in British Units.
Volume 1: Fundamentals and Non-Renewable Resources, 77–87.
the Metric System. Currently, the United States, Liberia, and Myanmar are the only
78 3 Units and Unit Conversions
Energy source Common measuring units
Oil Million barrels
Coal Million tonnes
Natural Gas Billion standard cubic feet
Uranium
Wood
Thousand tonnes
Cord
The units for measuring energy sources and their conversion factors are given
Unit Multiply by To obtain
Barrels of oil (bbl) 42 US gallons (gal)
Barrels of oil (bbl) 34.97 Imperial gallons (UK gal)
Barrels of oil (bbl) 0.136 Tonnes of oil equivalent (toe)
Barrels of oil (bbl) 0.1589873 Cubic meter (m3
)
Barrels of oil equivalent
(boe)
5,658.53 Cubic feet (ft3
) of natural gas
Tonnes of oil equivalent
(toe)
7.33*
Barrels of oil equivalent (boe)
Cubic yards (yd3
) 0.764555 Cubic meter (m3
)
Cubic feet (ft3
) 0.02831685 Cubic meter (m3
)
Cubic feet (ft3
) of natural gas 0.0001767 Barrels of oil equivalent (boe)
US gallons (gal) 0.0238095 Barrels (bbl)
US gallons (gal) 3.785412 Liters (l)
US gallons (gal) 0.8326394 Imperial gallons (UK gal)
Imperial gallons (UK gal) 1.201 US gallon (gal)
Imperial gallons (UK gal) 4.545 Liters (l)
Short tons 2,000 Pounds (lb)
Short tons 0.9071847 Metric tonnes (t)
Long tons 1.016047 Metric tonnes (t)
Long tons 2,240 Pounds (lb)
Metric tonnes (t) 1,000 Kilograms (kg)
Metric tonnes (t) 0.9842 Long tons
Metric tonnes (t) 1.102 Short tons
Pounds (lb) 0.45359237 Kilograms (kg)
Kilograms (kg) 2.2046 Pounds (lb)
Acres 0.40469 hectares (ha)
Square miles (mi2
) 2.589988 square kilometers (km2
)
Square yards (yd2
) 0.8361274 square meters (m2
)
Square feet (ft2
) 0.09290304 square meters (m2
)
Square inches (in2
) 6.4516 square centimeters (cm2
)
British Thermal Units (Btus) 1,055.05585262 joules (J)
Calories (cal) 4.1868 joules (J)
Kilowatt hours (kWh) 3.6 Megajoules (MJ)
Therms 100,000 British thermal units (Btus)
Table 3.1. Common measuring units used to describe common energy sources.
Table 3.2. Conversion factors for energy related units.
in Table 3.2. The conversion factors of various other units are given in Appendix III.
3.2 Basic Energy Units 79
Unit Multiply by To obtain
Tonnes of oil equivalent 10,000,000 Kilocalories (kcal)
Tonnes of oil equivalent 396.83 Therms
Tonnes of oil equivalent 41.868 Gigajoules (GJ)
Tonnes of oil equivalent 11,630 Kilowatt hours (kWh)
Cubic feet (ft3
) of natural gas 1,025 British Thermal Units (Btus)
* This conversion can range from 6.5 to 7.9 depending on the type of crude oil
It is important to understand both the units and how to convert British units to
metric units and vice versa. Various units used in energy systems and businesses
are explained below and their conversion factors are given in Appendix III.
3.2 Basic Energy Units
British Thermal Unit (BTU)
The BTU is defined as the amounts of energy required to raise one pound of water
at its maximum density, which occurs at a temperature of 39.1 degrees Fahrenheit
(o
F) by 1o
F at sea level.
Calorie (Cal)
Calorie is the equivalent of BTU in SI or Metric system of units. Calorie is defined
as the amounts of energy required to raise 1 g of water by one degree Celsius
(1o
C) from 14.5o
C to 15.5o
C at sea level.
Joule (J)
Joule is the unit of electrical, mechanical, and thermal energy in the SI system of
units. Depending on its use, its definition or interpretation is different.
As a unit of electrical energy, joule is the energy equal to the work done when a
current of 1 ampere is passed through a resistance of 1 ohm for 1 s.
As a unit of mechanical energy, it is the energy equal to the work done when a
force of 1 Newton acts through a distance of 1 m in the direction the force is
applied. This is also a unit of work which is equal to 107
units of work in the
Centimeter, the Gram, and the Second (CGS) system of units (ergs, the unit of
work or energy in the CGS system, equal to the work done by a force of 1 dyne
As a unit of thermal energy, it is defined as the amount of energy required to
raise the temperature of 1 kg of water by 1°C.
acting through a distance of 1 cm).
80 3 Units and Unit Conversions
In terms of kinetic energy, one joule is equal to the energy of a mass of 2 kg
moving at a velocity of one meter per second.
1 J/s = W
The conversion factors between these units are given below.
1 BTU = 251.9 cal
= 0.2519 kcal
= 1055 J
= 1.055 kJ
1 cal = 3.9698 10-3
BTU
= 4.1868 J
1 J = 0.2388 cal
= 9.4786 10-4
BTU
3.2.1 Other Energy Units
Quad
1 Quad = 1015
BTUs.
The United States used 101.6 quads per year in 2007.
Therm
1 Therm = 100,000 BTU
Often a number of prefixes are used with the regular units to describe large
amounts of energy. This is most common with the SI units. Some of these prefixes
used to describe energy units are given in Table 3.3.
A Quad is used when measuring large amounts of energy.
A Therm is another energy unit mainly used to describe energy content of natural gas.
3.3 Energy Content 81
Table 3.3. Prefixes used to describe large energy units.
Unit Equivalent
Kilowatt (kW) 1,000 (One Thousand) Watts
Megawatt (MW) 1,000,000 (One Million) Watts
Gigawatt (GW) 1,000,000,000 (One Billion) Watts
Terawatt (TW) 1,000,000,000,000 (One Trillion) Watts
Kilowatt-hours (kWh) 1,000 (One Thousand) Watt-hours
Megawatt-hours (MWh) 1,000,000 (One Million) Watt-hours
Gigawatt-hours (GWh) 1,000,000,000 (One Billion) Watt-hours
Terawatt-hours (TWh) 1,000,000,000,000 (One Trillion) Watt-hours
Source: Energy Information Administration, Office of Coal, Nuclear, Electric and
Cord
wide, 8 ft long and 4 ft high. It contains 128 ft3
of wood and space. It may contain
approximately 80–90 ft3
of solid wood. A common, but fairly meaningless conversion
is 500 board feet per cord.
3.3 Energy Content
It is important to understand the energy content of various energy resources that
are available throughout the world. Various countries in the world are rich in certain
resources. For example, the United States has very large coal reserves, it is
amount of land mass and therefore has access to solar energy, and it has a moderate
amount of oil reserves. Other countries are not as well off as the United States.
For example, France has a very poor energy resource base. It has chosen to go to
an all nuclear energy economy. Japan has a very poor energy resource base and,
like France, it too has chosen to go to an all nuclear energy economy. Other
countries such as Canada and Russia are rich in resources like the United States.
Countries in the Middle East are very rich in oil reserves. In order to compare the
values of these resources, energy content of all the resources is described by a
common unit, called tonne of oil equivalent (toe) or tonne of coal equivalent (tce).
However, the use of toe is more common than tce. The Statistics Division of the
United Nations Secretariat and the International Energy Agency defines one tonne
of oil equivalent as 107
kcal, net calorific value (equivalent to 41.868 GJ). The toe
of various energy sources is shown below.
Alternate Fuels, Electric Power Division [4].
A Cord is the unit of measure of wood that is equivalent to a pile of round wood 4 ft
rich in uranium reserves, it has a large amount of natural gas, it has a very good
resource base of wind energy, it has a rich resource base of hydro, it has a large
82 3 Units and Unit Conversions
1 t of crude oil = about 7.3 barrels
1 t of natural gas liquids = 45 GJ (net calorific value)
1,000 standard cubic meters of natural gas = 36 GJ (net calorific value)
1 t of uranium = 10,000–16,000 toe
1 t of peat = 0.2275 toe
1 t of fuelwood = 0.3215 toe
The average energy content of various energy sources in a common unit, such
as BTU are given below.
One barrel of crude oil equals to 42 gallons of crude oil, or 5.8 million BTUs
One cubic foot (ft3
)of natural gas equals to 1032 BTUs
One tonne of coal equals to 24 to 28 million BTUs
One cord of wood equals to 15–24 million BTUs
Solar heat is capable of providing 0.06 million BTUs per square foot per year
A 10 m or 33 ft in diameter windmill located in the Great Plains region of the
USA with an average wind speed of 20 mph can produce 49,000 kWh per year
or 167 million BTUs per year.
1 kg of U-235 can produce 78,000 million BTUs.
Example 3.1
How many barrels of crude oil are needed to supply the USA’s energy needs
for the year 2007?
Solution
Data: US uses about 101.6 quad energy per year.
1 quad = 1015
BTU
1 barrel of oil contents about 5.8 106
BTU of energy
barrels
BTUs
barrels 10
6
15
10752.1
108.5
106.101
#
Example 3.2
How many cubic feet of gas are needed to supply the USA’s energy needs for
the year 2007?
Solution
#Cubic feet = 101.6 1015
BTUs /(1.032 103
BTU/ft3
)
= 9.845 1013
ft3
BTU/barrel
3.3 Energy Content 83
Example 3.3
How many tons of coals are needed to supply the USA’s energy needs for the
year 2007?
Solution
#Tons = 101.6 1015
BTUs/(24 106
BTU/t) = 4.233 109
t
Example 3.4
How many square feet of land for solar energy are needed to supply the USA’s
Solution
#Square Feet = 101.6 1015
BTUs /(0.06 106
BTU/ft2
)
= 1.693 1012
ft2
This is about 61,101 square miles (Note: This is a square of about 247 by 247
miles.
cells are less than 10% efficient. Assuming 10% efficiency, to produce 101.6 Quads
of electrical energy by solar cells would take a land area of 611,010 square miles
(or a square of 782 by 782 miles). This is about the equivalent land area of Arizona,
New Mexico, Colorado, Utah, Nevada and Idaho (Arizona covers 114,006 square
miles, New Mexico covers 121,598 square miles, Colorado covers 104,100 square
miles, Utah covers 84,904 square miles, Nevada covers 110,567, and Idaho covers
83,574 square miles), or alternatively we could choose Texas, California, Nevada
and Utah (Texas covers 26,8601 square miles and California, covers 163,707
square miles).
Example 3.5
How many kg of U-235 are needed to supply the USA’s energy needs for the
year 2007?
Solution
#kg = 101.6 1015
106
BTU/kg) = 1.295 10 kg
= 1.426 10 t
efficiency)?
energy needs for the year 2007 (not considering the thermal energy conversion
The energy conversion problem is significant. The most cost effective solar
BTUs/(78,000 6
3
84 3 Units and Unit Conversions
Example 3.6
Energy Produced Per Plant = 0.9 1,200 106
W 1 J/s-W 1 year 365
day/year 24 h/day 60 min/h 60 s/min
9.4786 10-4
BTU/J
= 3.228 1013
BTU/Power Plant
The next step is to calculate the energy in hydrogen converted by electrolysis
using the electricity of the nuclear power plant.
Hydrogen Energy Produced per Power Plant = 0.5 3.228 1013
BTU/Power
Plant = 1.614 1013
BTU-Hydrogen/Power Plant
Number of Power Plants Needed for Transportation = 29.10 1015
BTU/1.614
1013
3.4 Power
We are involved every day with energy and power. For example, automobiles and
electrical motors are rated by Horsepower, light bulbs are sold by Watts, the price
of natural gas is set by Therms, the consumption of electricity is defined by kilowatt-hours,
and air conditioners are sold by Tons or BTUs per hour. Some of these
mental unit. From fundamental units, one can derive other essential parameters.
Kilowatt
BTUs per hour – British Thermal Units per hour
BTU/Power Plant = 1, 803 Power Plants
In 2007 the energy used by the US for transportation was 29.10 quads. How
many nuclear power plants would it take to produce enough hydrogen to provide
the energy needed for transportation? Assume that the conversion efficiency from
electricity to hydrogen using electrolysis is 50%. A typical nuclear power plant
produces about 1,200 MW electric. Assume that a nuclear power plant operates at
90% of its capacity (capacity factor) for the year. The first step is to calculate the
number of BTUs that a nuclear power plant produces in a year.
are described by energy units, while others are by power unit. Energy is a fundais
defined as the energy per unit time. The units of power are:
An example of this is power. Power is the rate at which energy is used. Power
3.4 Power 85
Kilowatt
Kilowatt-hour (kWh) is the metric unit of energy. It may be defined as the work or
energy equal to that expended by 1 kW in 1 h. One kilowatt-hour is equal to
3,600,000 J or 3.6 MJ, or 3,413 BTUs. Kilowatt, on the other hand, is the unit of
MMB/D
MMB/D (equivalent to a million barrels of oil per day) – if all of the energy used
by the US, 101.6 quads in 2007, were from oil than the United States uses about
48 MMB/D.
Tara Watt
Tara Watt = TW = 1 trillion watts
Example 3.7
How many kilowatt-hours does a 1 GWe nuclear power plant produce in a
year? Assume a capacity factor of 90%.
Solution
1 year = 1 year 365 days/year 24 h/day = 8,760 h
Energy = 1 106
kW 0.90 8,760 h = 7.884 109
kWh
Example 3.8
How many BTUs is 7.884 109
kWh?
Solution
Energy = 3,413 BTUs/kWh 7.884 109
kWh = 2.668 1013
BTUs
Example 3.9
How many Quads are in 2.668 1013
BTUs?
power. It is an energy use rate of 1,000 J per second.
86 3 Units and Unit Conversions
Solution
Energy = 2.668 1013
BTUs/(1015
BTUs/quad) = 2.668 10-2
quad
Example 3.10
How many MMB/D are in 2.668 10-2
quad?
Solution
Energy = 2.668 10-2 -2
MMB/D
Example 3.11
What percentage of the US energy use does a 1 GWe nuclear plant produce?
Solution
% of US Energy Produced = 100 1.284 10-2
MMB/D/(48 MMB/D) =
0.02675%
Example 3.12
It is given that a light bulb has a power rating 100 W. This is a rate at which the
Solution
Ten 100 W light bulbs turned on for 1 h is equivalent to:
100 W × 10 light bulbs × 1 h
Example 3.13
How many 100 W light bulbs will be required to consume 101.6 quads of
energy per year?
Solution
From the previous problem, one 100 W light bulb consumes 341.3 BTU per
hour. There are 24 h in a day. There are 365 days in a year and therefore 8,760 h
per year. Thus a single 100 W light bulb will use 2,989,788 BTUs per year if it is
on for the whole year.
Number of light bulbs = 101.6 1015
/2.989788 106
= 34 billion light bulbs
quad/(2.1 quad/MMB/D) = 1.284 10
bulb uses energy. What will be the energy consumption of ten, 100 W bulbs in 1 h
in British units?
= 1,000 W hours = 1 kWh = 3,413 BTU
Problems 87
References
1. Metric Act of 1866, Public Law 39-183, U.S. Congress, 28 July 1866.
2. U.S. Metric Study Act of 1968, Public Law 90-472, U. S. Congress, 9 August 1968.
Problems
2. The unit of viscosity in SI units is generally given in centipoise (g/(s cm). Convert 1
centipoise to British units (lb/(s ft).
4.
units (1) calorie, (2) joules, (3) ft-lb, and (4) kWh.
1.
2 3 3 2 3
3. 3
centimeters atm/(gmol K), (lb.in ) (ft )/(lbmol°R), (atm ft )/(lbmol R), and (lb/ft ) (ft )/
(lbmol°R)?
°
Thermal conductivity of water at 32°F in British units is 0.32 Btu/(h)(ft )( F/ft). Convert°
this to SI unit.
Calculate the energy content of (a) one barrel of crude oil (b) one cubic foot of natural
gas (c) one short ton of coal (d) one cord of wood (e) 1 kg of U 235 in the following
The universal Gas-law constant in cal/(gmol K) is 1.987. What is its value in cubic
3. Metric Conversion Act of 1975, Public Law 94-168, U. S. Congress, 23 December
1975.
4.
(3/23/2009) Electric Power.
Energy Information Administration, Office of Coal, Nuclear, Electric and Alternate Fuels