35
C H A P T E R T W O
Fundamentals of
Steam Power
2.1 Introduction
Much of the electricity used in the United States is produced in steam power plants.
Despite efforts to develop alternative energy converters, electricity from steam will
continue, for many years, to provide the power that energizes the United States and
world economies. We therefore begin the study of energy conversion systems with this
important element of industrial society.
Steam cycles used in electrical power plants and in the production of shaft power
in industry are based on the familiar Rankine cycle, studied briefly in most courses in
thermodynamics. In this chapter we review the basic Rankine cycle and examine
modifications of the cycle that make modern power plants efficient and reliable.
2.2 A Simple Rankine-Cycle Power Plant
The most prominent physical feature of a modern steam power plant (other than its
smokestack) is the steam generator, or boiler, as seen in Figure 2.1. There the
combustion, in air, of a fossil fuel such as oil, natural gas, or coal produces hot
combustion gases that transfer heat to water passing through tubes in the steam
generator. The heat transfer to the incoming water (feedwater) first increases its
temperature until it becomes a saturated liquid, then evaporates it to form saturated
vapor, and usually then further raises its temperature to create superheated steam.
Steam power plants such as that shown in Figure 2.1, operate on sophisticated
variants of the Rankine cycle. These are considered later. First, let’s examine the
simple Rankine cycle shown in Figure 2.2, from which the cycles of large steam power
plants are derived.
In the simple Rankine cycle, steam flows to a turbine, where part of its energy is
converted to mechanical energy that is transmitted by rotating shaft to drive an
electrical generator. The reduced-energy steam flowing out of the turbine condenses to
liuid water in the condenser. A feedwater pump returns the condensed liquid
(condensate) to the steam generator. The heat rejected from the steam entering the
condenser is transferred to a separate cooling water loop that in turn delivers the
rejected energy to a neighboring lake or river or to the atmosphere.
36
As a result of the conversion of much of its thermal energy into mechanical energy,
or work, steam leaves the turbine at a pressure and temperature well below the turbine
entrance (throttle) values. At this point the steam could be released into the
atmosphere. But since water resources are seldom adequate to allow the luxury of onetime
use, and because water purification of a continuous supply of fresh feedwater is
costly, steam power plants normally utilize the same pure water over and over again.
We usually say that the working fluid (water) in the plant operates in a cycle or
undergoes of cyclic process, as indicated in Figure 2.2. In order to return the steam to
the high-pressure of the steam generator to continue the cycle, the low- pressure steam
leaving the turbine at state 2 is first condensed to a liquid at state 3 and then
pressurized in a pump to state 4. The high pressure liquid water is then ready for its
next pass through the steam generator to state 1 and around the Rankine cycle again.
The steam generator and condenser both may be thought of as types of heat
exchangers, the former with hot combustion gases flowing on the outside of water-
37
filled tubes, and the latter with external cooling water passing through tubes on which
the low- pressure turbine exhaust steam condenses. In a well-designed heat exchanger,
both fluids pass through with little pressure loss. Therefore, as an ideal, it is common
to think of steam generators and condensers as operating with their fluids at
unchanging pressures.
It is useful to think of the Rankine cycle as operating between two fixed pressure
levels, the pressure in the steam generator and pressure in the condenser. A pump
provides the pressure increase, and a turbine provides the controlled pressure drop
between these levels.
Looking at the overall Rankine cycle as a system (Figure 2.2), we see that work is
delivered to the surroundings (the electrical generator and distribution system) by the
turbine and extracted from the surroundings by a pump (driven by an electric motor or
a small steam turbine). Similarly, heat is received from the surroundings (combustion
gas) in the steam generator and rejected to cooling water in the condenser.
38
At the start of the twentieth century reciprocating steam engines extracted thermal
energy from steam and converted linear reciprocating motion to rotary motion, to
provide shaft power for industry. Today, highly efficient steam turbines, such as shown
in Figure 2.3, convert thermal energy of steam directly to rotary motion. Eliminating
the intermediate step of conversion of thermal energy into the linear motion of a piston
was an important factor in the success of the steam turbine in electric power
generation. The resulting high rotational speed, reliability, and power output of the
turbine and the development of electrical distribution systems allowed the centralization
of power production in a few large plants capable of serving many industrial and
residential customers over a wide geographic area.
The final link in the conversion of chemical energy to thermal energy to mechanical
energy to electricity is the electrical generator. The rotating shaft of the electrical
generator usually is directly coupled to the turbine drive shaft. Electrical windings
attached to the rotating shaft of the generator cut the lines of force of the stator
windings, inducing a flow of alternating electrical current in accordance with Faraday's
Law. In the United States, electrical generators turn at a multiple of the generation
frequency of 60 cycles per second, usually 1800 or 3600 rpm. Elsewhere, where 50
cycles per second is the standard frequency, the speed of 3000 rpm is common.
Through transformers at the power plant, the voltage is increased to several hundred
thousand volts for transmission to distant distribution centers. At the distribution
centers as well as neighborhood electrical transformers, the electrical potential is
reduced, ultimately to the 110- and 220-volt levels used in homes and industry.
39
Since at present there is no economical way to store the large quantities of
electricity produced by a power plant, the generating system must adapt, from moment
to moment, to the varying demands for electricity from its customers. It is therefore
important that a power company have both sufficient generation capacity to reliably
satisfy the maximum demand and generation equipment capable of adapting to varying
load.
2.3 Rankine-Cycle Analysis
In analyses of heat engine cycles it is usually assumed that the components of the
engine are joined by conduits that allow transport of the working fluid from the exit of
one component to the entrance of the next, with no intervening state change. It will be
seen later that this simplification can be removed when necessary.
It is also assumed that all flows of mass and energy are steady, so that the steady
state conservation equations are applicable. This is appropriate to most situations
because power plants usually operate at steady conditions for significant lengths of
time. Thus, transients at startup and shutdown are special cases that will not be
considered here.
Consider again the Rankine cycle shown in Figure 2.2. Control of the flow can be
exercised by a throttle valve placed at the entrance to the turbine (state 1). Partial valve
closure would reduce both the steam flow to the turbine and the resulting power
output. We usually refer to the temperature and pressure at the entrance to the turbine
as throttle conditions. In the ideal Rankine cycle shown, steam expands adiabatically
and reversibly, or isentropically, through the turbine to a lower temperature and
pressure at the condenser entrance. Applying the steady-flow form of the First Law of
Thermodynamics [Equation (1.10)] for an isentropic turbine we obtain:
q = 0 = h2 – h1 + wt [Btu/lbm | kJ/kg]
where we neglect the usually small kinetic and potential energy differences between the
inlet and outlet. This equation shows that the turbine work per unit mass passing
through the turbine is simply the difference between the entrance enthalpy and the
lower exit enthalpy:
wt = h1 – h2 [Btu/lbm | kJ/kg] (2.1)
The power delivered by the turbine to an external load, such as an electrical generator,
is given by the following:
Turbine Power = mswt = ms(h1 – h2) [Btu/hr | kW]
where ms [lbm /hr | kg/s] is the mass flow of steam though the power plant.
40
Applying the steady-flow First Law of Thermodynamics to the steam generator,
we see that shaft work is zero and thus that the steam generator heat transfer is
qa = h1 – h4 [Btu/lbm | kJ/kg] (2.2)
The condenser usually is a large shell-and-tube heat exchanger positioned below or
adjacent to the turbine in order to directly receive the large flow rate of low-pressure
turbine exit steam and convert it to liquid water. External cooling water is pumped
through thousands of tubes in the condenser to transport the heat of condensation of
the steam away from the plant. On leaving the condenser, the condensed liquid (called
condensate) is at a low temperature and pressure compared with throttle conditions.
Continued removal of low-specific-volume liquid formed by condensation of the highspecific-volume
steam may be thought of as creating and maintaining the low pressure
in the condenser. The phase change in turn depends on the transfer of heat released to
the external cooling water. Thus the rejection of heat to the surroundings by the
cooling water is essential to maintaining the low pressure in the condenser. Applying
the steady-flow First Law of Thermodynamics to the condensing steam yields:
qc = h3 – h2 [Btu/lbm | kJ/kg] (2.3)
The condenser heat transfer qc is negative because h2 > h3. Thus, consistent with sign
convention, qc represents an outflow of heat from the condensing steam. This heat is
absorbed by the cooling water passing through the condenser tubes. The condensercooling-water
temperature rise and mass-flow rate mc are related to the rejected heat
by:
ms|qc| = mc cwater(Tout - Tin) [Btu/hr | kW]
where cwater is the heat capacity of the cooling water [Btu/lbm-R | kJ/kg-K]. The
condenser cooling water may be drawn from a river or a lake at the temperature Tin and
returned downstream at Tout, or it may be circulated through cooling towers where heat
is rejected from the cooling water to the atmosphere.
We can express the condenser heat transfer in terms of an overall heat transfer
coefficient, U, the mean cooling water temperature, Tm = (Tout + Tin)/2, and the
condensing temperature T3:
ms|qc| = UA(T3 - Tm) [Btu/hr | kJ/s]
It is seen for given heat rejection rate, the condenser size represented by the tube
surface area A depends inversely on (a) the temperature difference between the
condensing steam and the cooling water, and (b) the overall heat-transfer coefficient.
For a fixed average temperature difference between the two fluids on opposite
sides of the condenser tube walls, the temperature of the available cooling water
controls the condensing temperature and hence the pressure of the condensing steam.
41
Therefore, the colder the cooling water, the lower the minimum temperature and
pressure of the cycle and the higher the thermal efficiency of the cycle.
A pump is a device that moves a liquid from a region of low pressure to one of
high pressure. In the Rankine cycle the condenser condensate is raised to the pressure
of the steam generator by boiler feed pumps, BFP. The high-pressure liquid water
entering the steam generator is called feedwater. From the steady-flow First Law of
Thermodynamics, the work and power required to drive the pump are:
wp = h3 – h4 [Btu/lbm | kJ/kg] (2.4)
and
Pump Power = mswp = ms(h3 – h4) [Btu/hr | kW]
where the negative values resulting from the fact that h4 > h3 are in accordance with the
thermodynamic sign convention, which indicates that work and power must be supplied
to operate the pump.
The net power delivered by the Rankine cycle is the difference between the turbine
power and the magnitude of the pump power. One of the significant advantages of the
Rankine cycle is that the pump power is usually quite small compared with the turbine
power. This is indicated by the work ratio, wt / wp, which is large compared with one
for Rankine cycle. As a result, the pumping power is sometimes neglected in
approximating the Rankine cycle net power output.
It is normally assumed that the liquid at a pump entrance is saturated liquid. This
is usually the case for power-plant feedwater pumps, because on the one hand
subcooling would increase the heat edition required in the steam generator, and on the
other the introduction of steam into the pump would cause poor performance and
destructive, unsteady operation. The properties of the pump inlet or condenser exit
(state 3 in Figure 2.2) therefore may be obtained directly from the saturated-liquid
curve at the (usually) known condenser pressure.
The properties for an isentropic pump discharge at state 4 could be obtained from
a subcooled-water property table at the known inlet entropy and the throttle pressure.
However, such tables are not widely available and usually are not needed. The
enthalpy of a subcooled state is commonly approximated by the enthalpy of the
saturated-liquid evaluated at the temperature of the subcooled liquid. This is usually
quite accurate because the enthalpy of a liquid is almost independent of pressure. An
accurate method for estimating the pump enthalpy rise and the pump work is given later
(in Example 2.3).
A measure of the effectiveness of an energy conversion device is its thermal
efficiency, which is defined as the ratio of the cycle net work to the heat supplied from
external sources. Thus, by using Equations (2.1), (2.2), and (2.4) we can express the
ideal Rankine-cycle thermal efficiency in terms of cycle enthalpies as:
42
th = (h1 – h2 + h3 – h4)/(h1 – h4) [dl] (2.5)
In accordance with the Second Law of Thermodynamics, the Rankine cycle
efficiency must be less than the efficiency of a Carnot engine operating between the
same temperature extremes. As with the Carnot-cycle efficiency, Rankine-cycle
efficiency improves when the average heat-addition temperature increases and the heatrejection
temperature decreases. Thus cycle efficiency may be improved by increasing
turbine inlet temperature and decreasing the condenser pressure (and thus the
condenser temperature).
Another measure of efficiency commonly employed by power plant engineers is the
heat rate, that is, the ratio of the rate of heat addition in conventional heat units to the
net power output in conventional power units. Because the rate of heat addition is
proportional to the fuel consumption rate, the heat rate is a measure of fuel utilization
rate per unit of power output. In the United States, the rate of heat addition is usually
stated in Btu/hr, and electrical power output in kilowatts, resulting in heat rates being
expressed in Btu/kW-hr. The reader should verify that the heat rate in English units is
given by the conversion factor, 3413 Btu/kW-hr, divided by the cycle thermal efficiency
as a decimal fraction, and that its value has a magnitude of the order of 10,000
Btu/kW-hr. In the SI system of units, the heat rate is usually expressed in kJ/kW-hr, is
given by 3600 divided by the cycle efficiency as a decimal fraction, and is of the same
order of magnitude as in the English system. It is evident that a low value of heat rate
represents high thermal efficiency and is therefore desirable.
EXAMPLE 2.1
An ideal Rankine cycle (see Figure 2.2) has a throttle state of 2000 psia/1000°
F and
condenser pressure of 1 psia. Determine the temperatures, pressures, entropies, and
enthalpies at the inlets of all components, and compare the thermal efficiency of the
cycle with the relevant Carnot efficiency. Neglect pump work. What is the quality of
the steam at the turbine exit?
Solution
The states at the inlets and exits of the components, following the notation of
Figure 2.2, are listed in the following table. The enthalpy and entropy of state 1 may be
obtained directly from tables or charts for superheated steam (such as those in
Appendices B and C) at the throttle conditions. A Mollier chart is usually more
convenient than tables in dealing with turbine inlet and exit conditions.
For an ideal isentropic turbine, the entropy is the same at state 2 as at state 1. Thus
state 2 may be obtained from the throttle entropy (s2 = s1 = 1.5603 Btu/lbm-R) and the
condenser pressure (1 psia). In general, this state may be in either the superheatedsteam
region or the mixed-steam-and-liquid region of the Mollier and T-s diagrams. In
the present case it is well into the mixed region, with a temperature of 101.74°
F and an
enthalpy of 871 Btu/lbm.
43
The enthalpy, h3 = 69.73 Btu/lbm, and other properties at the pump inlet are obtained
from saturated-liquid tables, at the condenser pressure. The steady-flow First Law of
Thermodynamics, in the form of Equation (2.4), indicates that neglecting isentropic
pump work is equivalent to neglecting the pump enthalpy rise. Thus in this case
Equation (2.4) implies that h3 and h4 shown in Figure (2.2) are almost equal. Thus we
take h4 = h3 as a convenient approximation.
State Temperature
(°F)
Pressure
(psia)
Entropy
(Btu/lbm-°R)
Enthalpy
(Btu/lbm)
1 1000.0 2000 1.5603 1474.1
2 101.74 1 1.5603 871.0
3 101.74 1 0.1326 69.73
4 101.74 2000 0.1326 69.73
The turbine work is
h1 – h2 = 1474.1 – 871 = 603.1 Btu/lbm.
The heat added in the steam generator is
h1 – h4 = 1474.1 – 69.73 = 1404.37 Btu/lbm.
The thermal efficiency is the net work per heat added = 603.1/1404.37 = 0.4294
(42.94%). This corresponds to a heat rate of 3413/0.4294 = 7946 Btu/kW-hr. As
expected, the efficiency is significantly below the value of the Carnot efficiency
of 1 – (460 + 101.74)/(460 + 1000) = 0.6152 (61.52%), based on a source
temperature of T1 and a sink temperature of T3.
The quality of the steam at the turbine exit is
(s2 – sl)/(sv – sl) = (1.5603 – 0.1326)/(1.9781 – 0.1326) = 0.7736
Here v and l indicate saturated vapor and liquid states, respectively, at pressure p2.
Note that the quality could also have been obtained from the Mollier chart for steam as
1 - M, where M is the steam moisture fraction at entropy s2 and pressure p2.
__________________________________________________________________
Example 2-2
If the throttle mass-flow is 2,000,000 lbm/hr and the cooling water enters the condenser
at 60°F, what is the power plant output in Example 2.1? Estimate the cooling-water
mass-flow rate.
44
Solution: The power output is the product of the throttle mass-flow rate and the power
plant net work. Thus
Power = (2 × 106
)(603.1) = 1.206 × 109
Btu/hr
or
Power = 1.206 × 109
/ 3413 = 353,413 kW.
The condenser heat-transfer rate is
msqc = ms ( h3 – h2 ) = 2,000,000 × (69.73 – 871) = – 1.603×109
Btu/hr
The condensing temperature, T3 = 101.74 °F, is the upper bound on the cooling
water exit temperature. Assuming that the cooling water enters at 60°F and leaves at
95°F, the cooling-water flow rate is given by
mc = ms|qc| / [ cwater(Tout – Tin)] = 1.603×109
/[(1)(95 - 60)] = 45.68×106
lbm/hr
A higher mass-flow rate of cooling water would allow a smaller condenser coolingwater
temperature rise and reduce the required condenser-heat-transfer area at the
expense of increased pumping power.
____________________________________________________________________
2.4 Deviations from the Ideal – Component Efficiencies
In a power plant analysis it is sometimes necessary to account for non-ideal effects such
as fluid friction, turbulence, and flow separation in components otherwise assumed to
be reversible. Decisions regarding the necessity of accounting for these effects are
largely a matter of experience built on familiarity with the magnitudes of the effects,
engineering practices, and the uses of the calculated results.
Turbine
In the case of an adiabatic turbine with flow irreversibilities, the steady-flow First Law
of Thermodynamics gives the same symbolic result as for the isentropic turbine in
Equation (2.1), i.e.,
wt = h1 – h2 [Btu/lb | kJ/kg] (2.6)
except that here h2 represents the actual exit enthalpy and wt is the actual work of an
adiabatic turbine where real effects such as flow separation, turbulence, irreversible
internal heat transfers, and fluid friction exist.
45
An efficiency for a real turbine, known as the isentropic efficiency, is defined as
the ratio of the actual shaft work to the shaft work for an isentropic expansion between
the same inlet state and exit pressure level. Based on the notation of Figure 2.4, we see
that the turbine efficiency is:
turb = (h1 – h2 )/(h1 – h2s ) [dl] (2.7)
where h2s, the isentropic turbine-exit enthalpy, is the enthalpy evaluated at the turbine
inlet entropy and the exit pressure. For the special case of an isentropic turbine,
h2 = h2s and the efficiency becomes 1. Note how state 2 and the turbine work change
in Figure 2.4 as the efficiency increases toward 1. The diagram shows that the
difference between the isentropic and actual work, h2 – h2s, represents work lost due to
irreversibility. Turbine isentropic efficiencies in the low 90% range are currently
achievable in well-designed machines.
Normally in solving problems involving turbines, the turbine efficiency is known
from manufacturers’ tests, and the inlet state and the exhaust pressure are specified.
State 1 and p2 determine the isentropic discharge state 2s using the steam tables. The
actual turbine-exit enthalpy can then be calculated from Equation (2.7). Knowing both
p2 and h2, we can then fully identify state 2 and account for real turbine behavior in any
cycle analysis.
Pump
Work must be supplied to a pump to move liquid from a low pressure to a high
pressure. Some of the work supplied is lost due to irreversibilities. Ideally the remaining
effective work to raise the pressure is necessarily less than that supplied. In order for
46
the efficiency of a pump to be less than or equal to 1, it is defined in inverse fashion to
turbine efficiency. That is, pump efficiency is the ratio of the isentropic work to the
actual work input when operating between two given pressures. Applying Equation
(2.4) and the notation of Figure (2.5), the isentropic pump work, wps = h3 – h4s, and the
pump isentropic efficiency is
pump = wps /wp = (h4s – h3)/(h4 – h3) [dl] (2.8)
Note the progression of exit states that would occur in Figure 2.5 as pump efficiency
increases for a fixed inlet state and exit pressure. It is seen that the pump lost work,
given by h4 – h4s decreases and that the actual discharge state approaches the isentropic
discharge state.
States 4 and 4s are usually subcooled liquid states. As a first approximation their
enthalpies may be taken to be the saturated liquid enthalpy at T3. More accurate
approximations for these enthalpies may be obtained by applying the First Law for a
closed system undergoing a reversible process, Equation (1.8): Tds = dh - vdp. For an
isentropic process it follows that dh = vdp. Because a liquid is almost incompressible,
its specific volume, v, is almost independent of pressure. Thus, using the notation of
Figure 2.5, integration with constant specific volume yields
h4s = h3 + v3 ( p4 – p3 ) [Btu/lbm | kJ/kg]
where a knowledge of state 3 and p4 determines h4s.
47
Using Equation (2.8), and without consulting tables for subcooled water, we can
then calculate the pump work from
wp = v3(p3 – p4)/p [ft-lbf/lbm | kN-m/kg] (2.9)
Note that the appropriate conversion factors must be applied for dimensional
consistency in Equation (2.9).
EXAMPLE 2.3
Calculate the actual work and the isentropic and actual discharge enthalpies for an 80%
efficient pump with an 80°F saturated-liquid inlet and an exit pressure of 3000 psia.
Solution
From the saturated-liquid tables, for 80°F, the pump inlet conditions are 0.5068 psia,
48.037 Btu/lbm, and 0.016072 ft3
/lbm.
Using Equation (2.9), we find that the pump work is
wp = [0.016072(0.5068 – 3000)(144)]/0.8 = – 8677 ft-lbf / lbm
or
wp = – 8677/778 = – 11.15 Btu/lbm.
Note the importance of checking units here.
The actual discharge enthalpy is
h4 = h3 – wp = 48.037 – (–11.15) = 59.19 Btu/lbm.
and the isentropic discharge enthalpy is
h4s = h3 – p wp = 48.037 – (0.8)(– 11.15) = 56.96 Btu/lbm.
____________________________________________________________________
EXAMPLE 2.4
What is the turbine work, the net work, the work ratio, and the cycle thermal efficiency
for the conditions of Example 2.1 if the turbine efficiency is 90% and the pump
efficiency is 85%? What is the turbine exit quality?
Solution
By the definition of isentropic efficiency, the turbine work is 90% of the isentropic
turbine work = (0.9)(603.1) = 542.8 Btu/lbm.
By using Equation (2.9), the isentropic pump work is
[(0.01614)(1 – 2000)(144)] / 778 = – 5.97 Btu/lbm.
48
The actual pump work is then – 5.97/.85 = – 7.03 Btu/lbm and the work ratio is
542.8/| – 7.03| = 77.2
The cycle net work is wt + wp = 542.8 – 7.03 = 535.8 Btu/lbm..
Applying the steady-flow First Law of Thermodynamics to the pump, we get the
enthalpy entering the steam generator to be
h4 = h3 – wp = 69.73 – (– 7.03) = 76.76 Btu/lbm.
The steam-generator heat addition is then reduced to 1474.1 – 76.76 = 1397.3
Btu/lbm. and the cycle efficiency is 535.8/1397.3 = 0.383. Study of these examples
shows that the sizable reduction in cycle efficiency from that in Example 2.1 is largely
due to the turbine inefficiency, not to the neglect of pump work.
From Equation (2.6), the true turbine exit enthalpy is the difference between the
throttle enthalpy and actual turbine work = 1474.1 - 542.8 = 931.3 Btu/lbm.
The quality is then x = (h2 – hl)/(hv – hl) = (931.3 – 69.73)/(1105.8 – 69.73) =
0.832.
Thus the turbine inefficiency increases the turbine exhaust quality over the
isentropic turbine value of 0.774.
____________________________________________________________________
2.5 Reheat and Reheat Cycles
A common modification of the Rankine cycle in large power plants involves
interrupting the steam expansion in the turbine to add more heat to the steam before
completing the turbine expansion, a process known as reheat. As shown in Figure 2.6,
steam from the high-pressure (HP) turbine is returned to the reheat section of the steam
generator through the "cold reheat" line. There the steam passes through heated tubes
which restore it to a temperature comparable to the throttle temperature of the high
pressure turbine. The reenergized steam then is routed through the "hot reheat" line to
a low-pressure turbine for completion of the expansion to the condenser pressure.
Examination of the T-s diagram shows that reheat increases the area enclosed by
the cycle and thus increases the net work of the cycle by virtue of the cyclic integral,
Equation (1.3). This is significant, because for a given design power output higher net
work implies lower steam flow rate. This, in turn, implies that smaller plant components
may be used, which tends to reduce the initial plant cost and to compensate for added
costs due to the increased complexity of the cycle.
Observe from Figure 2.6 that the use of reheat also tends to increase the average
temperature at which heat is added. If the low-pressure turbine exhaust state is
superheated, the use of reheat may also increase the average temperature at which heat
is rejected. The thermal efficiency may therefore increase or decrease, depending on
specific cycle conditions. Thus the major benefits of reheat are increased net work,
49
drying of the turbine exhaust (discussed further later), and the possibility of improved
cycle efficiency.
Note that the net work of the reheat cycle is the algebraic sum of the work of the
two turbines and the pump work. Note also that the total heat addition is the sum of the
heat added in the feedwater and reheat passes through the steam generator. Thus the
50
thermal efficiency of the reheat cycle is:
(h1 – h2) + (h3 – h4) + (h5 – h6)
th = ----------------------------------- [dl] (2.10)
(h1 – h6) + (h3 – h2)
Relations such as this illustrate the wisdom of learning to analyze cycles using
definitions and applying fundamentals to components rather than memorizing equations
for special cases such as Equation (2.5) for the efficiency of the simple Rankine cycle.
Note that the inclusion of reheat introduces a third pressure level to the Rankine
cycle. Determination of a suitable reheat pressure level is a significant design problem
that entails a number of considerations. The cycle efficiency, the net work, and other
parameters will vary with reheat pressure level for given throttle and condenser
conditions. One of these may be numerically optimized by varying reheat pressure level
while holding all other design conditions constant.
Reheat offers the ability to limit or eliminate moisture at the turbine exit. The
presence of more than about 10% moisture in the turbine exhaust can cause erosion of
blades near the turbine exit and reduce energy conversion efficiency. Study of Figure
2.6 shows that reheat shifts the turbine expansion process away from the two-phase
region and toward the superheat region of the T-s diagram, thus drying the turbine
exhaust.
EXAMPLE 2.5
Reanalyze the cycle of Example 2.1 (2000 psia/1000°F/1 psia) with reheat at 200 psia
included. Determine the quality or degree of superheat at the exits of both turbines.
Assume that reheat is to the HP turbine throttle temperature.
Solution
Referring to Figure 2.6, we see that the properties of significant states are the
following:
State Temperature
(°F)
Pressure
(psia)
Entropy
(Btu/lbm-°R)
Enthalpy
(Btu/lbm)
1 1000.0 2000 1.5603 1474.1
2 400.0 200 1.5603 1210.0
3 1000.0 200 1.84 1527.0
4 101.74 1 1.84 1028.0
5 101.74 1 0.1326 69.73
6 101.74 2000 0.1326 69.73
51
Properties here are obtained from the steam tables and the Mollier chart as follows:
1. The enthalpy and entropy at state 1 are read from the superheated-steam tables
at the given throttle temperature and pressure.
2. State 2 is evaluated from the Mollier diagram at the given reheat pressure and
the same entropy as in state 1 for the isentropic turbine expansion.
3. Reheat at constant pressure p3 = p2 to the assumed throttle temperature T3 = T1
gives s3 and h3. Normally, T3 is assumed equal to T1 unless otherwise specified.
4. The second turbine flow is also specified as isentropic with expansion at s4 = s3
to the known condenser pressure p4.
5. The condenser exit (pump entrance) state is assumed to be a saturated liquid at
the known condenser pressure.
6. Pump work is neglected here. The steady-flow First Law then implies that
h6 = h5, which in turn implies the T6 = T5.
The turbine work is the sum of the work of both turbines:
(1474.1 - 1210) + (1527 - 1028) = 763.1 Btu/lbm.
The heat added in the steam generator feedwater and reheat passes is
(1474.1 - 69.73) + (1527 - 1210) = 1721.4 Btu/lbm.
The thermal efficiency then is 763.1/1721.4 = 0.443, or 44.3%.
Both the net work and the cycle efficiency are higher than in the simple Rankine
cycle case of Example 2.1. From the Mollier chart in Appendix B it is readily seen that
state 2 is superheated, with 400 - 381.8 = 18.2 Fahrenheit degrees of superheat; and
state 4 is wet steam, with 7.4% moisture, or 0.926 (92.6%) quality. Thus the first
turbine has no moisture and the second is substantially drier than 0.774 quality value in
Example 2.1.
____________________________________________________________________
Reheat is an important feature of all large, modern fossil-fueled steam power plants.
We now consider another key feature of these plants, but temporarily omit reheat, for
the purpose of clarity.
2.6 Regeneration and Feedwater Heaters
The significant efficiency advantage of the Carnot cycle over the Rankine cycle is due
to the fact that in the Carnot cycle all external heat addition is at a single high
52
temperature and all external heat rejection at a single low temperature. Examination of
Figures 2.2 and 2.6 shows that heat addition in the steam generator takes place over a
wide range of water temperature in both the simple and reheat Rankine cycles.
Presumably, the Rankine-cycle thermal efficiency could be improved by increasing the
average water temperature at which heat is received. This could be accomplished by an
internal transfer of heat from higher-temperature steam to low-temperature feedwater.
An internal transfer of heat that reduces or eliminates low-temperature additions of
external heat to the working fluid is known as regeneration.
Open Feedwater Heaters
Regeneration is accomplished in all large-scale, modern power plants through the use
of feedwater heaters. A feedwater heater (FWH) is a heat exchanger in which the latent
heat (and sometimes superheat) of small amounts of steam is used to increase the
temperature of liquid water (feedwater) flowing to the steam generator. This provides
the internal transfer of heat mentioned above.
An open feedwater heater is a FWH in which a small amount of steam mixes
directly with the feedwater to raise its temperature. Steam drawn from a turbine for
feedwater heating or other purposes is called extraction steam. Feedwater heaters in
which extraction steam heats feedwater without fluid contact will be discussed later.
Consider the regenerative Rankine-cycle presented in Figure 2.7. The steam
leaving the high-pressure (HP) turbine is split with a small part of the mass flow
extracted to an open FWH and the major part of the flow passing to a low pressure
(LP) turbine. The T-s diagram shows that steam entering the FWH at state 2 is at a
higher temperature than the subcooled feedwater leaving the pump at state 5. When the
two fluids mix in the FWH, the superheat and the heat of vaporization of the extraction
steam are transferred to the feedwater, which emerges with the condensed extraction
steam at a higher temperature, T6.. It is assumed that all streams entering and leaving
the FWH are the same pressure so that the mixing process occurs at constant pressure.
The T-s and flow diagrams show that heat from combustion gases in the steam
generator need only raise the water temperature from T7 to T1 rather than from T5 when
extraction steam is used to heat the feedwater. The average temperature for external
heat addition must therefore increase. Despite the reduced flow rate through the lowpressure
turbine, we will see by example that the thermal efficiency of the steam cycle is
improved by the transfer of energy from the turbine extraction flow to the feedwater.
The analysis of cycles with feedwater heaters involves branching of steam flows.
In Figure 2.7, for example, conservation of mass must be satisfied at the flow junction
downstream of the high-pressure-turbine exit. Thus, assuming a mass flow of 1 at the
HP turbine throttle and a steam mass-flow fraction, m1, through the feedwater heater,
the low-pressure-turbine mass-fraction must be 1 - m1. Note that the latter flow passes
through the condenser and pump and is reunited with the extraction flow, m1, in the
FWH at state 6, where the exit-flow-rate fraction is again unity.
53
It will be seen later that it is common for more than one FWH to be used in a
single power plant. When more than one FWH is present, mass flows m1, m2...mn are
defined for each of the n FWHs. Conservation of mass is used to relate these flows to
54
condenser flow rate and the reference throttle flow rate. This is accomplished by taking
a mass flow of 1 at the high-pressure-turbine throttle as a reference, as in the case of a
single FWH discussed above. After solving for each of the thermodynamic states and
FWH mass fractions, actual mass flow rates are obtained as the products of the known
(or assumed) throttle flow rate and FWH mass-flow fractions.
The function of feedwater heaters is to use the energy of extraction steam to
reduce the addition of low-temperature external heat by raising the temperature of the
feedwater before it arrives at the steam generator. Feedwater heaters are therefore
insulated to avoid heat loss to the surroundings. Because the resulting heat loss is
negligible compared with the energy throughflow, feedwater heaters are usually treated
as adiabatic devices.
In order to avoid irreversibility associated with unrestrained expansion, constant
pressure mixing of the streams entering the FWH is necessary. Returning to Figure 2.7,
this implies that the pressures of the feedwater at state 5 and at the FWH exit state 6
are chosen to be the same as that of the extraction steam at state 2.
Note that, as with reheat, the inclusion of a FWH also introduces an additional
pressure level into the Rankine cycle as seen in the T-s diagram. In the figure, the
extraction pressure level, p2, is another parameter under the control of the designer.
The extraction mass flow rate, m1, is in turn controlled by the designer’s choice of p2.
The mass-flow rate is determined by the physical requirement that the feedwater
entering the FWH at state 5 increase in temperature to T6 through absorption of the
heat released by the condensing extraction steam. This is accomplished by applying the
steady-flow First Law of Thermodynamics, using appropriate mass fractions, to the
insulated open FWH:
q = 0 = (1)h6 – m1h2 – (1 – m1 )h5 + 0 [Btu/lbm | kJ/kg]
Every term in this equation has dimensions of energy per unit throttle mass, thus
referring all energy terms to the mass-flow rate at the throttle of the high-pressure
turbine. For example, the second term on the right is of the form:
FWH Extraction mass Enthalpy at state 2 Enthalpy at state 2
-------------------------- × -------------------------- = ----------------------
Throttle mass FWH Extraction mass Throttle mass
Similarly, the structure of the third term on the right has the significance of
Pump mass Enthalpy at state 5 Enthalpy at state 5
---------------- × --------------------- = ----------------------
Throttle mass Pump mass Throttle mass
55
Solving for the extraction mass fraction, we obtain
m1 = (h6 – h5) / (h2 – h5) [dl] (2.11)
For low extraction pressures, the numerator is usually small relative to the
denominator, indicating a small extraction flow. The T-s diagram of Figure 2.7 shows
that increasing the extraction pressure level increases both h6 and h2. Thus, because the
small numerator increases faster than the large denominator, we may reason, from
Equation (2.11), that the extraction mass-flow fraction must increase as the extraction
pressure level increases. This conforms to the physical notion that suggests the need
for more and hotter steam to increase the feedwater temperature rise. While such
intuitions are valuable, care should be exercised in accepting them without proof.
The total turbine work per unit throttle mass flow rate is the sum of the work of
the turbines referenced to the throttle mass-flow rate. Remembering that 1 - m1 is the
ratio of the low-pressure turbine mass flow to the throttle mass flow, we obtain:
wt = (h1 – h2 ) + (1 – m1 )(h2 – h3 ) [Btu/lbm | kJ/kg] (2.12)
The reader should examine the structure of each term of Equation (2.12) in the light of
the previous discussion. Note that it is not important to remember these specific
equations, but it is important to understand, and be able to apply, the reasoning by
which they are obtained.
For a given throttle mass flow rate, mthr [lbm/s | kg/s], the total turbine power
output is given by mthrwt [Btu/s | kW].
We see in Figure 2.7 that the heat addition in the steam generator is reduced, due
to extraction at pressure p6 = p2, by about h7 – h5 to
qa = h1 – h7 [Btu/lbm | kJ/kg] (2.13)
At the same time, the net work also decreases, but more slowly, so that the net effect is
that the cycle efficiency increases with increased extraction.
EXAMPLE 2.6
Solve Example 2.1 (2000 psia /1000°F/1 psia) operating with an open feedwater heater
at 200 psia.
Solution
Referring to Figure 2.7, we find that the properties of significant states are:
56
State Temperature
(°F)
Pressure
(psia)
Entropy
(Btu/lbm-°R)
Enthalpy
(Btu/lbm)
1 1000.0 2000 1.5603 1474.1
2 400.0 200 1.5603 1210.0
3 101.74 1 1.5603 871.0
4 101.74 1 0.1326 69.73
5 101.74 200 0.1326 69.73
6 381.8 200 0.5438 355.5
7 381.8 2000 0.5438 355.5
States 1 through 4 are obtained in the same way as in earlier examples. Constant
pressure mixing requires that p5 = p6 = p2, the extraction pressure level. State 6, a
pump entrance state, is assumed to be a saturated-liquid state as usual. Subcooledliquid
states are approximated, as before, consistent with the neglect of pump work.
The extraction mass fraction obtained by applying the steady-flow First Law of
Thermodynamics to the FWH, Equation (2.11), is
m1 = (355.5 – 69.73)/(1210 – 69.73) = 0.251.
The net work (neglecting pump work) by Equation (2.12), is then
wn = (1474.1 – 1210) + (1 – 0.251)(1210 – 871) = 518.1 Btu/lbm
This may be compared with the simple-cycle net work of 603.1 Btu/lbm.
The heat added in the steam generator by Equation (2.13) is
qa = h1 – h7 = 1474.1 – 355.5 = 1118.6 Btu/lbm.
The resulting cycle efficiency is th = 518.1/1118.6 = 0.463, or 46.3%, a
significantly higher value than the 42.94% for the corresponding simple Rankine cycle.
Note, however, that the LP-turbine exhaust quality is the same as for the simple
Rankine cycle, an unacceptable 77.4%. This suggests that a combination of reheat and
regeneration through feedwater heating may be desirable. We will investigate this
possibility later after looking at closed feedwater heaters.
_____________________________________________________________________
Closed Feedwater Heaters
We have seen that feedwater heating in open feedwater heaters occurs by mixing of
extraction steam and feedwater. Feedwater heating also is accomplished in shell-and-
57
tube-type heat exchangers, where extraction steam does not mix with the feedwater.
Normally, feedwater passes through banks of tubes whereas steam condenses on the
outside of the tube surfaces in these heaters. Such heat exchangers are called closed
feedwater heaters.
Pumped Condensate. Closed feedwater heaters normally are employed in two
configurations in power plants. In the configuration shown in figure 2.8, condensate is
pumped from the condenser through the FWH and the steam generator directly to the
turbine along the path 4-5-8-9-1. Ideally, p5 = p1 assuming no pressure drop in the
FWH and steam generator.
Note that if m1 mass units of steam are extracted from the turbine for use in the
FWH, only 1 - m1 units of feedwater pass throught the condenser, pump, and the tubes
of the FWH. The condensed extraction steam (condensate) emerging from the FWH at
state 6 is pumped separately from p6 = p2 to throttle pressure p7 = p1, where it becomes
part of the steam generator feedwater. The pumped condensate at state 7 thus mixes
with the heated feedwater at state 8 to form the total feedwater flow at state 9.
Constant pressure mixing ( p7 = p8 = p9) is required at this junction to avoid losses
associated with uncontrolled flow expansion.
The enthalpy of the feedwater entering the steam generator can be determined by
applying the steady-flow First Law of Thermodynamics to the junction of the feedwater
and FWH streams:
h9 = (1 – m1 )h8 + m1h7 [Btu/lbm | kJ/kg]
As in the open FWH analysis, the extraction mass fraction depends on the choice
of intermediate pressure p2 and is obtained by applying the steady-flow First Law of
Thermodynamics to the feedwater heater.
Throttled Condensate. The second closed FWH configuration is shown in Figure
2.9 where the FWH condensate drops in pressure from p6 = p2 through a trap into the
condenser at pressure p7 = p3 = p4. The trap allows liquid only to pass from the FWH at
state 6 in a throttling process to state 7. As usual, it is assumed that the throttling
process is adiabatic. The T-s diagram shows that the saturated liquid at state 6 flashes
into a mixture of liquid and vapor in the condenser with no change in enthalpy, h7 = h6.
For this configuration, the closed FWH condensate mass-flow rate is equal to the
extraction mass-flow rate. As a result, conservation of mass applied to the condenser
shows that the mass-flow rate leaving the condenser and passing through the pump and
FWH tubes is the same as the throttle mass-flow rate. The throttled-condensate, closed
feedwater heater is the preferred configuration in power plants, because it is
unnecessary for each FWH to have a condensate pump.
58
59
60
EXAMPLE 2.7
Rework Example 2.1 (2000 psia/1000°F/1 psia) with reheat and a closed feedwater
heater with extraction from the cold reheat line and FWH condensate throttled to the
condenser. Both reheat and extraction are at 200 psia. Assume that the feedwater
leaving the FWH is at the temperature of the condensing extraction stream. Draw
appropriate T-s and flow diagrams.
Solution
Referring to the notation of Figure 2.10, verify that the significant the
thermodynamic state properties are:
State Temperature
(°F)
Pressure
(psia)
Entropy
(Btu/lbm-°R)
Enthalpy
(Btu/lbm)
1 1000.0 2000 1.5603 1474.1
2 400.0 200 1.5603 1210.0
3 1000.0 200 1.84 1527.0
4 101.74 1 1.84 1028.0
5 101.74 1 0.1326 69.73
6 101.74 2000 0.1326 69.73
7 381.8 200 0.5438 355.5
8 101.74 1 __ 355.5
9 381.8 2000 __ 355.5
Applying the steady-flow First Law of Thermodynamics to the FWH, we obtain:
0 = h9 + m1h7 – m1h2 – h6 + 0
which, solved for m1, yields:
m1 = ( h9 – h6 )/( h2 – h7 ) = (355.5 – 69.73)/(1210 – 355.5) = 0.3344
The total net work per unit of mass flow at the throttle of the HP turbine is the sum of
the specific work of each of the turbines adjusted for the HP turbine throttle mass flow:
wn = h1 – h2 + (1 – m1)( h3 – h4 )
= 1474.1 – 1210 + (1 – 0.3344)(1527 – 1028) = 596.2 Btu/lbm
61
62
As in the earlier examples in this series, pump work has been neglected.
The heat addition per unit HP-turbine-throttle mass is the sum of the heat addition
in the main pass and reheat pass through the steam generator, the latter as adjusted for
the reduced mass flow. Thus the steady-flow First Law of Thermodynamics yields
qa = h1 – h9 + (1 – m1 )( h3 – h2 )
= 1474.1 – 355.5 + (1 – 0.3344)(1527 – 1210) = 1329.6 Btu/lbm
The thermal efficiency of the cycle is wn / qa = 596.2 / 1329.6 = 0.448, or 44.8%.
The Mollier chart shows that the discharge of the first turbine (state 2) has 20
degrees of superheat and the second turbine (state 4) 7.4% moisture, or a quality of
0.926.
___________________________________________________________________
In the above calculation it was assumed that the feedwater temperature leaving the
FWH had risen to the temperature of the condensing extraction steam. Since the FWH
is a heat exchanger of finite area, the feedwater temperature T9 usually differs from the
condensing temperature of the extraction steam T7. If the surface area of the FWH is
small, the feedwater will emerge at a temperature well below the extraction-steam
condensing temperature. If the area were increased, the feedwater temperature would
approach the condensing temperature. This aspect of FWH design is reflected in the
parameter known as the terminal temperature difference, TTD, defined as
TTD = Tsat - Tfw [R | K]
where Tfw is the temperature of the feedwater leaving the tubes and Tsat is the
condensing temperature of the extraction steam in the closed FWH. In Figure 2.10, for
instance, Tfw = T9 and Tsat = T7. Thus, if the TTD and the extraction pressure are
known, the true FWH exit temperature may be determined. An application of the TTD
will be considered in a later example.
Table 2.1 summarizes, for comparison, the results of the calculations for the
several plant configurations that we have considered. The reader is cautioned that since
these calculations have not accounted for turbine inefficiency, the thermal efficiencies
are unusually high. While the efficiency differences with respect to the simple cycle may
seem insignificant, they are of great economic importance. It must be realized that
hundreds of millions of dollars may be spent on fuel each year in a power plant and that
capital costs are equally impressive. As a result, the choice of cycle and design
characteristics are of great significance. Some further improvement in net work and
efficiency could be shown by selecting extraction and reheat pressure levels to
maximize these parameters.
63
Table 2.1 Comparison of Rankine Cycle Modifications
Net Work
(Btu/lbm)
Efficiency
%
Heat Rate
(Btu/kW-hr)
Turbine Exit
Quality
Simple cycle 603.1 42.9 7956 0.774
Reheat cycle 763.1 44.3 7704 0.926
One open FWH 518.1 46.3 7371 0.774
One closed FWH
and reheat
596.2 44.8 7618 0.926
Multistage Extraction
It has been shown that increases in cycle efficiency may be accomplished in a steam
power plant through regeneration via the feedwater heater. Large steam power plants
typically employ large numbers of feedwater heaters for this purpose. Multistage
extraction refers to the use of multiple extractions to supply steam to these feedwater
heaters. Earlier discussions of examples involved extractions taken only from the flows
between turbines. However, the number of extractions is not limited by the number of
turbines. In fact, large turbines are designed with several extraction points through
which steam may be withdrawn for feedwater heating and other purposes.
Assigning Extraction-Pressure Levels. Given n feedwater heaters, it is necessary to
assign values to the n associated extraction pressures. For preliminary design purposes,
the extraction-pressure levels assigned may be those that give equal feedwater
temperature rises through each heater and through the steam generator to the boiling
point. Thus, for n heaters the appropriate temperature rise is given by
Topt = ( Tsl – Tcond )/( n + 1) [R | K] (2.14)
where Tsl is the temperature the saturated liquid at the throttle pressure and Tcond is the
temperature the feedwater leaving the condenser. The corresponding steam condensing
temperature in the ith heater is then
Ti = Tcond + ( i )Topt
= Tcond + i ( Tsl – Tcond )/( n + 1) [R | K] (2.15)
where i = 1, 2..., n. Steam tables may then be used to evaluate the corresponding
extraction-pressure levels. It is, of course, possible and sometimes necessary to assign
extraction-pressure levels in other ways.
64
EXAMPLE 2.8
Evaluate the recommended extraction-pressure levels for single heater for the
1000° F/2000 psia throttle and one psia condenser that have been used throughout this
chapter.
Solution
The feedwater temperature rise to establish an appropriate extraction-pressure
level for a single heater for a plant such as that shown in Figures 2.7 through 2.9 is
(Tsl – T4 )/2 = (635.8 – 101.74)/2 = 267.05°F where Tsl was evaluated at p1 = 2000
psia. This would make T6 = 101.74 + 267.05 = 368.79°F and the corresponding
extraction pressure level p6 = p2 = 171 psia, using the saturated-steam tables.
____________________________________________________________________
At this point we have the tools necessary to evaluate the performance and penalties
associated with a given configuration. The following example examines the gains that
follow from the use a single feedwater heater and the sensitivity of the thermal
efficiency to the assigned feedwater temperature rise.
EXAMPLE 2.9
Consider a single open feedwater heater operating in a Rankine cycle with a 2000 psia
saturated-vapor throttle and a 1 psia condenser. Evaluate the thermal efficiency as a
function of feedwater temperature rise. Compare the temperature rise that maximizes
the thermal efficiency with the results of Equation (2.14).
Solution
Utilizing the notation of Figure 2.7 and taking the throttle state as a saturated vapor,
we get the results that are summarized in spreadsheet format in Table 2.2. (This table is
a direct reproduction of a Quattro Pro spreadsheet used in the analysis. Care should be
taken if this spreadsheet is used for "what if" studies, because it is dependent on manual
entry of thermodynamic properties. To explore other cases, appropriate properties must
be obtained from steam tables or charts and inserted in the spreadsheet. Despite this
drawback, the spreadsheet provides a convenient means of organizing, performing, and
displaying calculations.) Details of the methodology are given in the right-most column.
It is seen that the net work drops, as expected, as more extraction steam is used to heat
the feedwater. Figure 2.11 shows the percentage increase in thermal efficiency as a
function of the feedwater temperature rise for this case. Over a 9% increase in thermal
efficiency is achieved with feedwater temperature rises between 200/F and 300°F.
Thus the prediction of Topt = 267°F using Equation (2.14) in Example 2.8 is clearly in
this range.
_____________________________________________________________________
65
Example 2.9 shows that improved thermal efficiency is achieved over a broad range of
feedwater temperature rise and therefore extraction pressure. This gives the designer
freedom to assign extraction-pressure levels so as to make use of existing designs for
feedwater heaters and turbines without severely compromising the efficiency of the
plant design.
Calculation Methodology. Once the extraction- and reheat-pressure levels are
established for a cycle with multistage extraction, and once throttle and condenser
conditions, turbomachine efficiencies, and FWH terminal temperature differences are
known, significant state properties should be determined. Symbols for extraction
mass-fraction variables should be assigned for each heater and related to other
unknown flows using mass conservation assuming unit mass flow at the highpressure-turbine
throttle. The steady-flow First Law of Thermodynamics should then
be applied to each of the FWHs, starting with the highest extraction pressure and
progressing to the lowest-pressure FWH. Analyzing the heaters in this order allows
each equation to be solved immediately for a mass fraction rather than solving all of
the equations simultaneously. Important performance parameters such as thermal
efficiency, net work, and work ratio may then be evaluated taking care to account
properly for component mass flows. The following example illustrates this
methodology.
66
67
EXAMPLE 2.10
Consider a power plant with 1000/F/2000-psia throttle, reheat at 200 psia back to
1000/F, and 1-psia condenser pressure. The plant has two closed feedwater heaters,
both with terminal temperature differences of 8/F. The high-pressure (HP) heater
condensate is throttled into the low-pressure (LP) heater, which in turn drains into the
condenser. Turbomachine efficiencies are 0.88, 0.9, and 0.8 for the HP turbine, the LP
turbine, and the boiler feed pump, respectively. Draw relevant T-s and flow diagrams
and evaluate FWH mass fractions, thermal efficiency, net work, and work ratio.
Solution
The notation used to study this plant is shown in Figure 2.12. The pertinent
thermodynamic properties and part of the analysis are presented in the spreadsheet
given in Table 2.3. The earlier-stated caution (Example 2.9) about using spreadsheets
that incorporate external data applies here as well, because changing parameters may
require changes in steam-table lookup values.
To start the analysis we first determine the extraction-pressure levels. The ideal
FWH temperature rise is given by
( Tsl – T7 )/3 = ( 635.8 – 101.74)/3 = 178.02°F
where the saturation temperature is evaluated at the HP-turbine throttle pressure of
2000 psia. The corresponding extraction condensing temperatures and extractionpressure
levels are
101.74 + 178.02 = 280/F $ p9 = p5 = 49 psia
and
101.74 + (2)(178.02) = 457.8°F $ p12 = p2 = 456 psia
where the extraction pressures have been evaluated using the saturated-steam tables.
After the entropy and enthalpy at state 1 are evaluated, the enthalpy h3s at the HPturbine
isentropic discharge state 3s is determined from s1 and p3. The HP-turbine
efficiency then yields h3 and the steam tables give s3. The entropy and enthalpy at the
HP-turbine extraction state 2 may be approximated by drawing a straight line on the
steam Mollier diagram connecting states 1 and 3 and finding the intersection with the
HP-extraction pressure P2. This technique may be used for any number of extraction
points in a turbine.
Once the hot reheat properties at state 4 are determined from the steam tables, the
LP-turbine exit and extraction states at 6 and 5 may be obtained by the same method
used for the HP turbine.
68
69
The determination of the FWH condensate temperatures and pressures at states 9
and 12 have already been discussed. The temperatures of the heated feedwater leaving
the FWHs may be determined from the terminal temperature differences:
T11 = T9 - TTD = 281 - 8 = 273°F
T14 = T12 - TTD = 457.5 - 8 = 449.5°F
Recalling that the enthalpy of a subcooled liquid is almost independent of pressure, we
note that the enthalpies h11 and h14 may be found in the saturated-liquid tables at T11 and
T14, respectively.
70
The pump discharge state 8 is a subcooled-liquid state, which may be
approximated in the same way as in Examples 2.3 and 2.4. Thus
h8s = h7 + ( p8 – p7 )v7
= 69.7 + (2000 – 1)(144)(0.016136)/778 = 75.7 Btu/lbm
and
h8 = h7 + ( h8s – h7 )/p = 69.7 + (75.7 – 69.7)/0.8 = 77.2 Btu/lbm
The pump work is then
wp = h7 – h8 = 69.7 – 77.2 = – 7.5 Btu/lbm
The extraction mass-flow fractions designated m1 and m2 relate other flows to the
unit mass flow at the high-pressure-turbine throttle. For example, the condensate flow
rate from the LP heater at state 10 is given by m1 + m2.
The steady-flow First Law of Thermodynamics may now be applied to the heaters.
For the HP FWH:
0 = m1h12 + (1)h14 – m1h2 – (1)hll
may be rewritten as
m1 = ( h14 – hll )/( h2 – h12 ) [dl]
This and the T-s diagram show that the HP extraction-flow enthalpy drop from
state 2 to state 12 provides the heat to raise the enthalpy in the feedwater from state 11
to state 14. Also, for the LP FWH:
0 = (1)hll + (m2
+ m1 )h9
– (1)h8
– m2h5 – mlhl3
becomes
m2 = [ m1( h9 - h13 ) + h11 – h8 ]/( h5 – h9 ) [dl]
This and the T-s diagram show that the discharge from the HP FWH at state 13 aids
the mass flow m2 in heating the LP FWH flow from state 8 to state 11. The values of
m1 and m2 are evaluated at the bottom of spreadsheet in Table 2.3.
71
With all states and flows known, we may now determine some plant performance
parameters. The turbine work referenced to the throttle mass-flow rate is easily
obtained by summing the flow contributions through each section of the turbines:
wt = h1 – h2 + (1 – ml )( h2 – h3) + (1 – ml )( h4 – h5)
+ (1 – ml – m2 )( h5 – h6) [Btu/lbm | kJ /kg]
The net work is then wt + wp, and the heat added in the steam generator is the sum of
heat additions in the feedwater pass and the reheat pass:
qa = h1 - h14 + (1 - ml )( h4 - h3) [Btu/lbm | kJ/kg]
These parameters and the work ratio are evaluated in Table 2.3.
____________________________________________________________________
Example 2.10 shows that a good thermal efficiency and net work output are
possible with the use of two feedwater heaters despite taking into account realistic
turbomachine inefficiencies. The high work ratio clearly demonstrates the lowcompression
work requirements of Rankine cycles.
2.7 A Study of a Modern Steam Power Plant
Modern steam power plants incorporate both reheat and feedwater heating. A
flowsheet for the Public Service Company of Oklahoma (PSO) Riverside Station Unit
#1, south of Tulsa, is shown in Figure 2.13. This natural-gas-burning plant was sized
for two nominal 500-megawatt units. Several other plants in the PSO system have
similar unit flowsheets, including a coal-burning plant. Note the flowsheet coding W, H,
F, and A for flow rate in lbm/hr, enthalpy in Btu/lbm, temperature in °F, and pressure in
psia, respectively.
The steam generator, not shown on the flowsheet, interacts through the feedwater
and steam lines on the right-hand side of the diagram. The high pressure turbine throttle
is at 1000°F and 3349 psia and has a mass-flow rate of 2,922,139 lbm/hr. This type of
unit is called supercritical, because the pressure in the main steam line to the HPturbine
throttle exceeds the 3208.2-psia critical pressure of steam. Note that a large
fraction of the HP-turbine mass-flow rate enters the cold reheat line at 630 psia and is
reheated to the intermediate-pressure (IP) turbine throttle conditions of 1000°F and
567 psia.
Most of the steam flow through the IP turbine passes through the crossover at 186
psia to the double-flow low-pressure (DFLP) turbine. The term double-flow refers to
the fact that the incoming flow enters at the middle, splits, and flows axially in opposite
72
73
directions through the turbine. This causes the large axial force components on the
blades and shaft to oppose each other so that the resultant axial thrust is small and does
not necessitate heavy thrust bearings. The combined HP and IP turbines are similarly
configured.
The plant is equipped with six closed FWHs and one open FWH (the deaerator).
Note that the condensate of each of the closed feedwater heaters is throttled to the next
lowest pressure FWH or, in the case of the lowest-pressure heater, to the condenser.
The extraction steam for the four lowest-pressure FWHs flows from the DFLP turbine.
Extraction steam for the highest pressure FWH is provided by the HP turbine, and the
IP turbine supplies heater HTR1-6 and the open feedwater heater identified as the
deaerator. The deaerator is specially designed to remove non-condensable gases from
the system, in addition to performing its feedwater heating duties.
The feedwater starts at the "hot well" of the condenser on the left of the diagram,
enters the condensate pump at 101.1°F and 2"Hg abs., and starts its passage through
the FWHs. Note that the feedwater increases in temperature from 102.1° to 180°,
227.2°, 282.7°, and 314.4° in passing through the 4 lowest pressure FWHs. The
feedwater from the deaerator is pumped to 405 psia by the booster pump and
subsequently to 3933 psia by the boiler feed pump (BFP). The BFP exit pressure
exceeds the HP-turbine throttle pressure of 3349 psia in order to overcome flow losses
in the high pressure heater, the boiler feed line, the steam generator main steam pass,
and the main steam line, all of which operate at supercritical pressure.
The boiler feed pump turbine (BFPT) shown in the upper left of the diagram
supplies the shaft power to drive the BFP at the lower right. The BFPT receives steam
from an extraction line of the DFLP turbine and exhausts directly to the condenser.
The reader should study Figure 2.13 thoroughly in the light of the preceding
discussions of reheat and feedwater heating. It is particularly useful to consider the flow
rates with respect to mass and energy conservation. Mastery of this flow sheet will
make it possible to quickly understand flowsheets of other major power plants.
Example 2.11
Verify that the steam generator feedwater flow rate satisfies the conservation of mass
into all the feedwater heaters shown for the Riverside Unit #1 in Figure 2.13. You may
neglect all flows of less than 2000 lbm/hr.
Solution
The shell side of the low pressure heater, labeled HTR1-1, receives condensate
from heaters 2, 3 and 4 as well as steam entering from the LP turbine. The total
condensate from the low-pressure heaters into the condenser are:
74
Source Flow rate, lbm/hr
_______________________________________________
Condensate from HTR1-4 75,005
Extraction steam into HTR1-3 125,412
Extraction steam into HTR1-2 102,897
----------
Total condensate into HTR1-1 303,314
Extraction steam into HTR1-1 157,111
---------
Total condensate leaving HTR1-1 460,425
The feedwater flow rate through the four low-pressure heaters (the condenser
condensate pump flow rate) is the sum of the flows into the condenser:
460,425 + 162,701 + 1,812,971 = 2,436,097 lbm/hr.
An easier approach to evaluating this flow rate is by imagining a control volume
around the entire left side of the diagram that cuts it in two parts between the deaerator
and HTR1-4 and through the crossover steam line. Because these are the only points
where the control volume is penetrated by large mass flows, the two flows must be
equal. Consequently the crossover mass-flow rate of 2,434,357 lbm/hr agrees very well
with our above calculation of the feedwater flow rate into the deaerator.
Now, observing that the boiler feedwater all flows from the deaerator through the
booster pump, we sum all of the flows into the deaerator:
Feedwater into deaerator 2,434,357
Steam to deaerator 148,321
Steam to HTR1-6 107,661
Steam to HTR1-7 222,876
-----------
Total feedwater into HTR1-7 2,913,215 lbm/hr
This compares well with the tabulated value of 2,922,139 lbm /hr to the steam
generator. Accounting for the small flows should improve the agreement.
______________________________________________________________
75
2.8 Deviations from the Ideal - Pressure Losses
It is evident from study of Figure 2.13 that there are significant pressure drops in the
flows through the steam generator between the HP FWH and the HP-turbine throttle
and in the reheat line between the HP and IP turbines. While we have neglected such
losses in our calculations, final design analysis requires their consideration. A first
attempt at this may be made by applying a fractional pressure drop based on
experience. Two per cent pressure drops through the main steam and feedwater lines
and a 3.7% loss through the steam generator would, for instance, account for the
indicated 14.8% loss from the boiler feed pump to the HP turbine.
In the final analysis, of course, when realistic values are available for flow rates and
properties, known fluid mechanic relations for pressure drop may be employed to
account for these losses.
Bibliography and References
1. Anon., Steam, Its Generation and Use. New York: Babcock and Wilcox, 1978.
2. Singer, J. G., (Ed.), Combustion/Fossil Power Systems. Windsor, Conn.:
Combustion Engineering, 1981.
3. Wood, Bernard, Applications of Thermodynamics, 2nd
ed. Reading, Mass.: AddisonWesley,
1981.
4. Li, Kam W., and Priddy, A. Paul, Powerplant System Design. New York: Wiley,
1985.
5. El-Wakil, M. M., Power Plant Technology. New York: McGraw-Hill, 1984.
6. Skrotzi, B. G. A. and Vopat, W. A., Power Station Engineering and Economy.
New York: McGraw-Hill, 1960.
EXERCISES
2.1 An ideal Rankine-cycle steam power plant has 800-psia saturated steam at the
turbine throttle and 5-psia condenser pressure. What are the turbine work, pump work,
net work, steam generator heat addition, thermal efficiency, maximum cycle
temperature, and turbine exit quality? What is the Camot efficiency corresponding to
the temperature extremes for this cycle?
2.2 A Rankine-cycle steam power plant has an 800-psia/900/F throttle and 5-psia
condenser pressure. What are the net work, turbine work, pump work, steam generator
76
heat addition, thermal efficiency, and turbine exit quality? What is the Carnot efficiency
corresponding to the temperature extremes for this cycle?
2.3 Solve Exercise 2.2 for the cases of (a) an 85% efficient turbine, (b) an 85%
efficient pump, and (c) both together. Tabulate and discuss your results together with
those of Exercise 2.2.
2.4 Solve Exercise 2.2 for the case of (a) 1000/F throttle, (b) 2000-psia throttle,
(c) 2-psia condenser, and (d) all three changes simultaneously. Make a table comparing
net work, quality, and thermal efficiency, including the results of Exercise 2.2. What
conclusions can you draw from these calculations?
2.5 Sketch coordinated, labeled flow and T-s diagrams for the ideal Rankine cycle.
Tabulate the temperatures, entropies, pressures, enthalpies, and quality or degree of
superheat for each significant state shown on the diagram for a throttle at 1000 psia and
1000/F and a condenser at 5 psia. Determine the net work, heat added, thermal
efficiency, heat rate, and heat rejected in the condenser. If the power plant output is
100 megawatts and the condenser cooling-water temperature rise is 15 Rankine
degrees, what is the steam flow rate and cooling-water flow rate? Neglect pump work.
2.6 Consider a simple Rankine cycle with a 2000-psia/1100/F throttle and 1-psia
condenser. Compare the thermal efficiencies and net work for cycles with a perfect
turbine and one having 86% turbine isentropic efficiency. Assume isentropic pumping.
2.7 A boiling-water reactor operates with saturated vapor at 7500 kPa at the throttle
of the high-pressure turbine. What is the lowest turbine exit pressure that ensures that
the turbine exit moisture does not exceed 12% if the turbine is isentropic? What would
the lowest pressure be if the turbine isentropic efficiency were 85%?
2.8 Consider a steam plant with a single reheat and a single open feedwater heater that
takes extraction from the cold reheat line. Sketch carefully coordinated and labeled T-s
and flow diagrams. If the throttle is at 1000/F and 3000psia, the condenser is at 1 psia,
and reheat is to 1000/F at 400 psia, what is the extraction mass fraction, the heat rate,
and the thermal efficiency? The turbine efficiency is 89%. Neglect pump work.
2.9 A Rankine-cycle power plant condenses steam at 2 psia and has 1000/F and 500
psia at the turbine throttle. Assume an isentropic turbine.
(a) Tabulate the temperature, pressure, entropy, and enthalpy of all states. Determine
the quality and moisture fraction for all mixed states.
(b) Calculate the heat transferred in the condenser and the steam generator and the
turbine work, all per unit mass. What is the thermal efficiency?
(c) Calculate the pump work. What is the ratio of turbine to pump work?
77
(d) What is the turbine work and thermal efficiency if the turbine efficiency is 85%?
Include pump work.
2.10 For throttle conditions of 1000/F and 1000 psia and a condenser pressure of 2
psia, compare the net work, thermal efficiency, and turbine discharge quality or degree
of superheat for a simple cycle and two reheat cycles with reheat to 1000/F at 50 and
200 psia. Tabulate your results. Sketch a single large, labeled T-s diagram comparing
the cycles. Turbine isentropic efficiencies are 85%.
2.11 Consider a regenerative Rankine cycle with a 1000/F and 500-psia throttle, 2-psia
condenser, and an open feedwater heater operating between two turbines at 50 psia.
Turbine efficiencies are 85%. Neglect pump work.
(a) Draw labeled, coordinated T-s and flow diagrams.
(b) Determine the fraction of the throttle mass flow that passes through the extraction
line.
(c) Calculate the turbine work per unit mass at the throttle.
(d) Calculate the cycle efficiency, and compare it to the simple-cycle efficiency.
2.12 Consider a 1120°F, 2000-psia, 10-psia steam cycle with reheat at 200 psia to
1000/F and a closed feedwater heater taking extraction from a line between two
turbines at 100psia. The FWH condensate is throttled to the condenser, and the
feedwater in the FWH is raised to the condensing temperature of the extraction steam.
(a) Draw labeled T-s and flow diagrams for this plant.
(b) Tabulate the enthalpies for each significant state point.
(c) What is the extraction fraction to the FWH?
(d) What are the net work and work ratio?
(e) What are the thermal efficiency and the heat rate?
2.13 A turbine operates with a 860/F, 900-psia throttle. Calorimetric measurements
indicate that the discharge enthalpy is 1250 Btu/lbm at 100 psia. What is the isentropic
efficiency?
2.14 An ideal Rankine cycle has 1000-psia saturated steam at the turbine throttle. The
condenser pressure is 10psia. What are the turbine work, steam generator heat addition,
maximum cycle temperature, turbine exit quality, and Carnot efficiency corresponding
to the temperature extremes of the cycle? Neglect pump work.
2.15 Assume that the extraction mass-flow rate to FWH #7 in Figure 2.13 is not
known. Calculate the FWH extraction mass fraction (relative to the HP-turbine throttle
flow) and the extraction mass-flow rate. Compare the extraction-steam energy loss rate
with the feedwater energy gain rate.
78
2.16 Compare the inflow and outflow of steam of the DFLP turbine in Figure 2.13,
and calculate the percentage difference. Calculate the power output of the DFLP
turbine in Btu/hr and in kW.
2.17 Calculate the power delivered by the PSO Riverside Unit #1 boiler feed pump
turbine, BFPT. Based on the feedwater enthalpy rise across the BFP, determine its
power requirements, in kilowatts. What fraction of the plant gross output is used by the
BFPT?
2.18 Without performing a detailed analysis of the FWHs, determine the PSO
Riverside Unit #1 feedwater flow rate from heater number 4 to the deaerator. Explain
your methodology.
2.19 Total and compare the inflows and outflows of mass and energy to the PSO
Riverside Unit #1 deaerator.
2.20 Rework Example 2.4 neglecting pump work. Repeat your calculations for an 80%
efficient pump. Compare and comment on the significance of accounting for pump
work and turbomachine efficiency.
2.21 For a 1080/F, 2000-psia, 5-psia Rankine cycle with 85% turbine efficiency and
60% pump efficiency:
(a) Compare the actual net work and the isentropic turbine work and the isentropic net
work.
(b) Calculate the actual heat transfer and work for each component, and evaluate the
cyclic integrals of Q and W.
(c) Compare the real cycle efficiency with that for the ideal Rankine cycle.
2.22 For a 1080/F, 2000-psia, 5-psia Rankine cycle with 85% turbine efficiency and
60% pump efficiency, evaluate the effect of a single reheat to 1080/F at 500 psia on:
(a) Heat addition in the steam generator.
(b) Work of each turbine, total turbine work, and net work. Compare the net work
with the cyclic integral of the external transfers of heat.
(c) Cycle efficiency and heat rate.
(d) Quality or degree of superheat at the exit of the turbines.
Draw labeled flow and T-s diagrams.
2.23 Consider a 1080/F, 2000-psia, 5-psia Rankine cycle with 85% turbine efficiency
and 60% pump efficiency. Compare the simple cycle with the same cycle operating with
a single reheat to 1080/F at 1000 psia with respect to:
(a) Heat addition in the steam generator.
(b) Work of each turbine, total turbine work and net work, condenser heat rejection,
and cyclic integral of heat added.
79
(c) Cycle efficiency.
(d) Quality or degree of superheat at the exit of the turbines.
Draw labeled flow and T-s diagrams.
2.24 For a 1080/F, 2000-psia, 5-psia Rankine cycle with 85% turbine efficiencies and
60% pump efficiencies and using a single open feedwater heater operating at 500 psia:
(a) Draw labeled and coordinated flow and T-s diagrams.
(b) Evaluate the feedwater heater mass fraction.
(c) Evaluate heat addition in the steam generator, work of each turbine, total turbine
work, and net work, all per pound of steam at the HP-turbine throttle.
(d) Evaluate condenser heat transfer per unit mass at the HP-turbine throttle.
(e) Evaluate cycle efficiency and heat rate. Compare with simple-cycle efficiency.
(f) Evaluate the cyclic integral of the differential heat addition, and compare it with
the net work.
2.25 Consider a 1080/F, 2000-psia, 5-psia Rankine reheat-regenerative cycle with
perfect turbomachinery and a closed feedwater heater taking extraction from the cold
reheat line at 500 psia. FWH condensate is pumped into the feedwater line downstream
of the feedwater heater. Assume that the enthalpy of the feedwater entering the steam
generator is that of the saturated liquid leaving the FWH.
(a) Draw coordinated and labeled flow and T-s diagrams.
(b) Determine the extraction mass fraction, the net work, and the total heat addition.
(c) Determine the thermal efficiency and heat rate.
(d) Determine the superheat or quality at the turbine exhausts:
2.26 Taking the reheat-pressure level as a variable, plot net work, thermal efficiency,
and turbine exhaust superheat and/or moisture against reheat pressure for the
conditions of Example 2.5. Select a suitable design value based on your analysis.
2.27 Solve Example 2.6 for 1200/F throttle substituting a closed FWH for the open
heater. Consider two cases in which the FWH condensate is (a) throttled to the
condenser, and (b) pumped to throttle pressure.
2.28 Solve Example 2.6 using the method for assigning extraction-pressure levels
given in the subsection of Section 2.6 on multistage extraction systems.
2.29 Solve Example 2.7 using the method for assigning extraction-pressure levels
given in the section on multistage extraction systems, and determine by trial and error
the reheat-pressure level that maximizes the thermal efficiency.
2.30 Solve Example 2.7 with the extraction condensate from the closed FWH pumped
ahead to the feedwater-pressure level.
80
2.31 Solve Example 2.6 for 900/F throttle temperature with the open FWH replaced
by a closed FWH where the feedwater is (a) throttled to the condenser, and (b) pumped
into the feedwater line downstream of the FWH.
2.32 Compare the work and exhaust quality of 90% efficient turbines with 2500-psia
throttle pressure and 1000/F and 1200/F throttle temperatures exiting to a 2-psia
condenser.
2.33 Draw a large T-s diagram showing the states associated with the important flows
of the PSO Riverside Unit #1 (Figure 2.13).
2.34 A Rankine-cycle steam power plant has 5-MPa saturated steam at the turbine
throttle and 25-kPa condenser pressure. What are the net work, steam generator heat
addition, thermal efficiency, heat rate, maximum cycle temperature, and turbine exit
quality? What is the Carnot efficiency corresponding to the temperature extremes for
this cycle?
2.35 A Rankine-cycle steam power plant has a 5-MPa/450/C throttle and 10-kPa
condenser pressure. What are the net work, steam generator heat addition, thermal
efficiency, heat rate, and turbine exit quality? What is the Carnot efficiency
corresponding to the temperature extremes for this cycle?
2.36 Solve Exercise 2.35 for the cases of (a) an 85% efficient turbine, (b) an 85%
efficient pump, and (c) both together. What conclusions may be inferred from your
results?
2.37 Solve Exercise 2.35 for the case of (a) a 550/C throttle, (b) a 15-MPa throttle,
(c) a 5-kPa condenser, and (d) all three changes simultaneously. What conclusions can
you draw from these calculations?
2.38 Sketch coordinated, labeled flow and T-s diagrams for the following Rankine
cycle. Tabulate the temperatures, entropies, pressures, enthalpies, and quality or degree
of superheat for each significant state shown on the diagram for a throttle at 10 MPa
and 550/C and condenser at 5 kPa. Determine the net work, heat added, thermal
efficiency, and heat rejected in the condenser. If the power plant output is 100
megawatts and the condenser cooling water temperature rise is 15/Rankine, what is the
steam flow rate and cooling-water flow rate? Neglect pump work.
2.39 Consider a Rankine cycle with a 20MPa/600/C throttle and 3-kPa condenser.
Compare the thermal efficiencies and net work for cycles with a perfect turbine and one
having 86% turbine isentropic efficiency.
81
2.40 Consider a steam plant, with a single reheat and a single open feedwater heater,
that takes extraction from the cold reheat line. Sketch carefully coordinated and labeled
T-s and flow diagrams. If the throttle is at 550/C and 15 MPa, the condenser is at 5
kPa, and reheat is to 3 MPa and 550° C, what are the extraction mass fraction, work
ratio, and thermal efficiency? The pump and turbine efficiencies are 82% and 89%,
respectively.
2.41 A Rankine-cycle power plant condenses steam at 10 kPa and has 550/C and 5
MPa at the turbine throttle. Assume an isentropic turbine.
(a) Tabulate the temperature, pressure, entropy, and enthalpy of all states. Determine
the quality and moisture fraction for all mixed states.
(b) Calculate the heat transferred in the condenser and steam generator and the turbine
work, all per unit mass. What is the thermal efficiency?
(c) Calculate the pump work. What is the ratio of turbine to pump work?
(d) What is the turbine work and thermal efficiency if the turbine efficiency is 85%?
Include pump work.
2.42 For throttle conditions of 550°C and 5 MPa and a condenser pressure of 10 kPa,
compare the net work, thermal efficiency, and turbine discharge quality or degree of
superheat for a simple cycle and two reheat cycles. Consider reheat to 500/C at (a)
4MPa and (b) 1 MPa. Tabulate and compare your results. Sketch a large, labeled T-s
diagram for a reheat cycle. Turbine efficiencies are 85%.
2.43 Consider a regenerative Rankine cycle with a 600/C and 4-MPa throttle, a 5-kPa
condenser, and an open feedwater heater at 500 kPa. Turbine efficiencies are 85%.
Neglect pump work.
(a) Draw labeled, coordinated T-s and flow diagrams.
(b) Determine the fraction of the throttle mass flow that passes through the extraction
line.
(c) Calculate the turbine work per unit mass at the throttle.
(d) Calculate the cycle efficiency, and compare it with the simple-cycle efficiency.
(e) Calculate the heat rate.
2.44 Consider a 600/C, 15-MPa steam cycle with reheat at 2 MPa to 600/C and
extraction to a closed feedwater heater at 600 kPa. The FWH condensate is throttled to
the condenser at 5 kPa, and the feedwater in the FWH is raised to the condensing
temperature of the extraction steam. Neglecting pump work:
(a) Draw labeled T-s and flow diagrams for this plant.
(b) Tabulate the enthalpies for each significant state point.
(c) What is the extraction fraction to the FWH?
(d) What is the net work?
(e) What is the thermal efficiency?
82
(f) What is the heat rate?
2.45 A turbine operates with a 600°C, 7-MPa throttle. Calorimetric measurements
indicate that the discharge enthalpy is 3050 kJ/kg at 0.8 MPa. What is the turbine
isentropic efficiency?
2.46 A pressurized water-reactor nuclear power plant steam generator has separate
turbine and reactor water loops. The steam generator receives high-pressure hot water
from the reactor vessel to heat the turbine feedwater. Steam is generated from the
feedwater in the turbine loop. The water pressure in the reactor is 15 MPa, and the
water temperature in and out of the reactor is 289°C and 325°C, respectively. The plant
has one turbine with a single extraction to a closed FWH with condensate throttled to
the condenser. Throttle conditions are 300/C and 8 MPa. The extraction and condenser
pressures are 100 kPa and 5 kPa, respectively. The reactor-coolant flow rate is 14,000
kg/s. Assume no heat losses in heat exchangers and isentropic turbomachines. Neglect
pump work.
(a) What is the rate of heat transfer from the reactor in MWt?
(b) Draw coordinated flow and T-s diagrams that show both loops.
(c) Determine the extraction mass fraction of the throttle flow rate.
(d) Determine the cycle net work, heat rate, and thermal efficiency.
(e) Calculate the steam flow rate.
(f) Assuming the electrical generator has 97% efficiency, calculate the power output,
in MWe (electric).
2.47 Perform an optimization of the extraction pressure of a Rankine cycle with a
2000-psia saturated-vapor throttle, a 1-psia condenser with a single closed feedwater
heater, as in Example 2.9. Compare the optimum extraction temperature given by
Equation (2.14) with your results.
2.48 Prepare an optimization study of thermal efficiency with a table and plot of net
work and thermal efficiency as a function of reheat pressure level for Example 2.5.
Discuss the selection of reheat pressure for this case. How does the reheat pressure
used in Example 2.5 compare with your results?
2.49 Solve Exercise 2.25 for reheat and extraction at 200 psia. Compare the extraction
mass fraction, net work, thermal efficiency, heat rate, and turbine exit conditions with
those of Exercise 2.25.
2.50 Rework Exercise 2.25, accounting for 90% turbine efficiencies and a 10/F
terminal temperature difference.
2.51 A 1000/F/2000-psia-throttle high-pressure turbine discharges into a cold reheat
line at 200 psia. Reheat is to 1000/F. The low-pressure turbine discharges into the
83
condenser at 0.5 inches of mercury absolute. Both turbines are 90% efficient. Design
the cycle for the use of three feedwater heaters. Draw coordinated T-s and flow
diagrams. State and discuss your decisions on the handling of the feedwater heater
design.
2.52 A steam turbine receives steam at 1050/F and 3000 psia and condenses at 5 psia.
Two feedwater heaters are supplied by extraction from the turbine at pressures of 1000
psia and 200 psia. The low-pressure heater is an open FWH, and the other is closed
with its condensate throttled to the open heater. Assuming isentropic flow in the turbine
and negligible pump work:
(a) Sketch accurately labeled and coordinated T-s and flow diagrams for the system,
and create a table of temperature, pressure, and enthalpy values for each state.
(b) What are the extraction flows to each feedwater heater if the throttle mass flow
rate is 250,000 pounds per hour?
(c) How much power, in kW, is produced by the turbine?
(d) Compare the thermal efficiency of the system with the efficiency if valves of both
extraction lines are closed.
(e) What is the heat rate of the system with both feedwater heaters operative?
2.53 Apply the steady-flow First Law of Thermodynamics to a single control volume
enclosing the two turbines in Example 2.7. Show that the same equation is obtained for
the turbine work as when the work of individual turbines is summed.
2.54 Apply the steady-flow First Law of Thermodynamics to a single control volume
enclosing the two turbines in Example 2.10. Show that the same equation is obtained
for the turbine work as when the work of individual turbines is summed.
2.55 Resolve Example 2.7 with 4% pressure drops in the main steam pass and reheat
pass through the steam generator. Make a table comparing your results with those of
the example to show the influence of the losses on plant performance. Calculate and
display the percentage differences for each parameter. Assume turbine throttle
conditions are unchanged.
2.56 Draw labeled and coordinated T-s and flow diagrams for a steam power plant
with 1000°F / 3000-psia / 2" Hg absolute conditions, assuming isentropic
turbomachinery. The plant has reheat at 500 psia to ll00/F. The plant has the following
feedwater heaters:
1. A closed FWH with extraction at 1000 psia and pumped condensate.
2. A closed FWH at 400 psia with condensate throttled into the next-lowestpressure
FWH.
3. An open FWH at 20 psia.
Define mass fraction variables. Show mass-flow variable expressions, with arrows
indicating mass fractions along the various process paths on the T-s and flow diagrams.
84
Write equations for conservation of energy for the FWHs that allow you to solve easily
for the mass fractions in terms of known state enthalpies and other mass fractions.
Indicate a solution method for the mass fractions that involves simple substitution only.
2.57 A pressurized-water nuclear-reactor steam generator has separate turbine and
reactor loops. The steam generator linking the two loops cools high-pressure hot water
from the reactor vessel and transfers the heat to the turbine feedwater producing steam.
The water pressure in the reactor is 2250 psia, and the water temperatures in and out of
the reactor are 559°F and 623°F, respectively. The plant has one turbine with a single
extraction to an open FWH. Throttle conditions are 555/F and 1100 psia. The
extraction and condenser pressures are 100 psia and 1 psia, respectively. The reactorcoolant
flow rate is 147,000,000 lbm/hr. Assume no heat losses in heat exchangers and
isentropic turbomachines.
(a) What is the rate of heat transfer from the reactor, in Btu/hr and in MWt?
(b) Draw coordinated flow and T-s diagrams that show both loops with states in their
proper relations with respect to each other.
(c) Determine the extraction mass fraction relative to the throttle flow rate.
(d) Determine the cycle net work.
(e) What are the cycle thermal efficiency and heat rate?
(f) Calculate the turbine-steam flow rate.
(g) Assuming the electrical generator has 100% efficiency, calculate the turbine power,
in Btu/hr and in MWe.
2.58 Determine the efficiencies of the boiler feed pump and boiler feed pump turbine of
the PSO Riverside Station Unit 4/1 (Figure 2.13).
2.59 A Rankine cycle with a single open feedwater heater has a 1040/F and 550-psia
throttle. Extraction from the exit of the first turbine (assumed isentropic) is at 40/F of
superheat. The second turbine has an efficiency of 85% and expands into the condenser
at 5 psia.
(a) Draw matched, labeled T-s and flow diagrams.
(b) Accurately calculate and tabulate the enthalpies of all significant states. Neglect
pump work.
(c) What is the feedwater-heater mass fraction relative to the mass flow at the first
throttle?
(d) What is the quality or degree of superheat at the condenser inlet?
(e) What are the net work, thermal efficiency, and heat rate?
(f) Estimate the feedwater-heater condensate pump work and its percentage of turbine
work.